Siemens DTF4301 Инструкции по установке и эксплуатации - Страница 2
Просмотреть онлайн или скачать pdf Инструкции по установке и эксплуатации для Посудомоечная машина Siemens DTF4301. Siemens DTF4301 2 страницы.
Печатать страницуMaintenance and care
Strainers ...
Rotate filter
cylinder, remove
Check, if
filter system ...
required, clean
Spray arms ...
Pull lower arm
upwards ...
Remove
blockages/deposits
Eliminating minor faults yourself ...
Fault
Possible Cause
Residual water in the device
Waste-water pump blocked
Programme not yet ended
Device does not work/stops
Supply fitting not open
Supply hose kinked
Supply fitting jammed or calcified
Plastic parts / parts of
Too little cleaning product
dishes discoloured
Discoloration caused by food colourings
(tomato sauce)
Interrupting the programme
–
Switch off the main switch.
–
To continue the programme,
switch on the main switch
again.
For perfect rinsing results ...
rinse under
flowing water ...
Unscrew upper
arm ...
... Self-help pays!
Remedy
Clean waste-water pump (see above).
Close and switch on the appliance and
wait until the programme ends (end of
programme display lights up) or
terminate programme (see Terminating
the programme).
Open supply fitting.
Lay supply hose without kinks.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 9 l/min when
the water inlet is open.
If the flow rate is less, replace the
supply fitting.
Follow manufacturer's specifications
(detergent).
Discoloration is quite safe; fades after
subsequent rinse cycles.
Cancelling the programme
While the programme is running,
simultaneously press the two
Reset buttons for approx.
3 seconds (RESET).
Insert ...
Clean spray nozzles
Insert lower arm ...
under flowing water
(perhaps with
toothpick) ...
Fault
Possible Cause
Dishes not clean
Utensils are situated too close to each
other or on top of each other
Sand or grainy residues
on dishes
Too little cleaning product
Unsuitable programme selected
Spray nozzles blocked
Filters dirty, not installed securely
Spray arms blocked
Stains and streaks
Rinse aid dosage too high / too low
Milky residues on dishes
Water softening system incorrectly set;
(can be removed)
no special salt
Milky film, glasses cloudy /
Glasses not dishwasher-proof.
dull (cannot be removed)
Cutlery rusty
Cutlery not rust-proof
Hard knife blades are more susceptible
Extraneous rust
1 minute after the
programme has
Switch off the
ended, the "pro-
appliance.
gramme end" dis-
play illuminates.
Cleaning the waste-water pump *
* With some models
Screw in filter system
– Ladle out water and remove filters
NOTE MARK!
– Unscrew cover (Torx T20)
– Check area of fan impeller for foreign objects
– Screw in cover and insert filters
Screw in upper arm
Remedy
Spread out the utensils, avoid contact
between the utensils.
Follow manufacturer's specifications
(detergent).
Select more intensive programme.
Clean spray arms (see above).
Clean the strainers (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Streaks: Reduce dosage.
Water or limescale stains:
Increase dosage.
Set water softening system correctly.
Refill with special salt.
Use dishwasher-proof glasses.
Use glass-friendly cleaning products.
Use dishwasher-proof cutlery.
Never wash rusting parts in the
appliance.
Further advice can be found in the instruction manual
Arranging utensils
correctly
Arrange dishwasher-proof utensils (without any residual ash, wax, grease,
ink, sticky labels; remove large remnants of jam, dairy products and food)
according to the operating instructions and check that the spray arms can
rotate freely.