Cisco AIR-AP1020 - 1000 Series Lightweight Access Point Краткое руководство по эксплуатации - Страница 16

Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для Беспроводная точка доступа Cisco AIR-AP1020 - 1000 Series Lightweight Access Point. Cisco AIR-AP1020 - 1000 Series Lightweight Access Point 44 страницы. Aironet 1000 series ieee 802.11a/b/g lightweight access points with external antennas

Печатать страницу

1. Installation and Configuration

Pre-Installation Configuration

Does My Cisco Aironet 1000 Series Lightweight Access Point Qualify for this Procedure?

If your 3.0 or later version Cisco Aironet 1000 Series lightweight access point(s) cannot be configured

for any reason using the following procedure, refer to the

Configuration Steps for a Cisco Aironet 1000 Series Lightweight Access Point

To configure an access point, perform these steps:

Configure the Cisco Wireless LAN Controller in LWAPP Layer 3 Mode and be sure its DS Port is

Step 1

connected to the network.

When you are installing a Cisco 1030 remote edge lightweight access point, a DHCP server must be

Note

accessible by the access point.

Step 2

Take the Cisco Aironet 1000 Series lightweight access point out of the box and plug it into the same

subnet as the Cisco Wireless LAN Controller.

Apply power to the Cisco Aironet 1000 Series lightweight access point.

Step 3

Note

Cisco Aironet 1000 Series 802.11a/b/g lightweight access points support 802.3af Power over Ethernet

(PoE). These access points do not support Cisco prestandard PoE. Please use Cisco 802.3af capable PoE

switches or power injectors.

AP1020/1030 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with External Antennas - Quick Start Guide

78-17147-01

Be sure Cisco Aironet 1000 Series lightweight access point ports are available through the Cisco

Wireless LAN Controller Management/AP-Manager Interface.

Set the Cisco Wireless LAN Controller as the Master so that new Cisco Aironet 1000 Series

802.11a/b/g lightweight access points always associate with it. Use the CLI command show network

config to determine if the Cisco Wireless LAN Controller DS Port is the Master. If the Cisco

Wireless LAN Controller DS Port is not, make it the Master using the CLI command config network

master-base disable.

Use 802.3af-compatible PoE from the Cisco Wireless LAN Controller or from an orderable inline

power injector. If you do not have PoE available, use an orderable external AC-to-48 VDC Power

Supply plugged into the side of the Cisco Aironet 1000 Series lightweight access point.

After you power up the Cisco Aironet 1000 Series lightweight access point, the RED Alarm LED

comes on for about 15-20 seconds and then all the LEDs blink sequentially back and forth,

indicating that the Cisco Aironet 1000 Series lightweight access point is trying to find a Cisco

Wireless LAN Controller to associate with. This can continue for up to five minutes. If the Cisco

Aironet 1000 Series lightweight access point remains in this mode for more than five minutes, the

Cisco Aironet 1000 Series lightweight access point is unable to find the Master Cisco Wireless LAN

Controller. Check the connection between the Cisco Aironet 1000 Series lightweight access point

and the Cisco Wireless LAN Controller and be sure the Cisco Aironet 1000 Series lightweight

access point and the Cisco Wireless LAN Controller are on the same subnet.

If the power light does not come on, check the power (it can be powered either with PoE or from an

orderable Cisco Aironet 1000 Series lightweight access point External Power Supply.

Be sure that a DHCP server is configured in the Cisco Wireless LAN Controller for both the

Management Interface and AP-Manager Interface using the CLI, Web User Interface, or Cisco WCS

interface, and that the DHCP server is operating correctly.

Installation and Configuration

"Obtaining Technical

Assistance" section.