CRU DataPort HotDock External Drive Bay Краткое руководство по эксплуатации - Страница 3

Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для Хранение CRU DataPort HotDock External Drive Bay. CRU DataPort HotDock External Drive Bay 5 страниц.

Печатать страницу
For PC Users
Windows 98SE, 2K, ME & XP
•
•
Available FireWire or USB 2.0 Port
For Mac Users
•
Mac OS 9.7 & X
Available FireWire or USB Port
•

Mounting a Hard Drive in the Carrier

1.
Remove the carrier top and bottom covers:
The metal covers for the carrier are snapped into place on the
carrier without any screws. Use the supplied cover removal tool or
a small flat-head screwdriver to gently pry the covers off.
2.
Set the jumper on the drive to master before placing the drive in
the carrier.
3.
Connect the DC power cable to the drive:
Plug the 4-pin DC power cable into the power connector on the
drive and ensure it is fully seated.
4.
Connect the data cable in the carrier to the drive.
5.
Install the drive in the carrier:
Place the drive in the carrier. Use the four screws provided to
mount the drive. Position the cables inside the carrier assembly so
that they are completely enclosed within the carrier.
6.
Insert the carrier into the HotDock:
Ensure that the lock of the carrier is in the "open" (vertical)
position. Position the carrier on the guide rails, then slide the
carrier into the frame. Using thumb pressure, fully seat the carrier
in the frame and then lock the unit with the keylock. (Required for
operation.)

Setting up the Drive for Windows 98

W
Formatting your drive will result in loss of data.
1.
To install a drive on your computer via the USB port you must
download the drivers from CRU-DataPort's website
(www.CRU-DataPort.com ). Navigate to the website.
2.
On the left side of the web page you will see a link titled
Click the Support link, then click USB Drivers, and then select
the Windows 98SE USB drivers link.
Page 4
!
ARNING
Support
.
www.CRU-DataPort.com
3.
Download the Win98 file and follow the instructions on the website
to install it.
4.
Connect the DataPort HotDock to your computer with either the
USB or FireWire cable. Connect the power supply providing power
to your DataPort HotDock. Turn on the power switch located on
the back of the enclosure.
Power
switch
Back of DataPort HotDock
The Device Driver Wizard will pop up.
5.
Click Next. The "recommended" option will be selected: click
Next. The wizard will be set to install the software automatically.
6.
Click Next and the wizard will ask where to look for the driver.
7.
Select the directory that you opened the driver into or select the
primary drive and let the computer find it.
8.
Once the driver installation is completed, click Close.

Setting up the Drive for Windows 2000

Formatting your drive will result in loss of data.
1.
Right-click the My Computer icon and select Properties.
2.
Select the Device Manager tab.
3.
Click the plus sign (+) beside Disk Drives.
4.
Right-click your drive icon and select Properties.
5.
Select the Settings tab, place a check beside Removable and
then assign it a drive letter.
6.
After completing these steps, reboot your computer. Once your
computer has booted up you should see an additional icon on your
Task Bar.
7.
Double-click My Computer. Your new drive should now be listed.
8.
Double-click the drive icon.
incompatible format
, it will ask you to format it:
a.
Click Yes. A new window will open. At the top, the capacity
of your drive will be listed; directly below that will be a section
Format Type
titled
.
www.CRU-DataPort.com
W
!
ARNING
If it is a new drive or a drive with an
Page 5