CRU DataPort HotDock External Drive Bay Краткое руководство по эксплуатации - Страница 4

Просмотреть онлайн или скачать pdf Краткое руководство по эксплуатации для Хранение CRU DataPort HotDock External Drive Bay. CRU DataPort HotDock External Drive Bay 5 страниц.

Печатать страницу
b.
In the Format Type section, select Full and then select Start.
Read and follow the instructions to finish setting up your drive.
REMEMBER, formatting your drive will result in loss of data.
9.
After connecting the DataPort™ HotDock to your computer, turn on
the power switch on the back of the enclosure (see the figure at
the top of page 5). A window will open for the New Hardware
Wizard. Follow the instructions to add the new drive.
10. After completing the instructions for adding a new hard drive, right-
click the My Computer icon and select Manage.
11. In the Storage sub-section, click Disk Management to display a
list of all the drives connected to your computer.
If you have not used the drive before, you will have to partition it:
a.
To partition the hard drive, from the Action menu select All
Tasks and then select Create Partition.
formatting will result in loss of data.
The Create Partition Wizard opens.
b.
Follow the onscreen instructions and the drive will be ready to
use.

Setting up the Drive for Windows XP and ME

W
Formatting your drive will result in loss of data.
1.
After connecting the DataPort HotDock to your computer, turn on
the power using the power switch on the back of the enclosure
(see figure on page 5). Check to see if the hard disk drive is
accessible in My Computer. If it does NOT show up, do the
following:
2.
Right-click the My Computer icon and select Manage.
3.
In the Storage sub-section, click Disk Management; this will
show all the drives connected to your computer.
4.
If you are prompted to initialize the drive, follow the directions.
REMEMBER, formatting your drive will result in loss of data.
You should now see the hard disk drive in the list of drives on the
right side of your window.
5.
Right-click the drive icon and select New Partition. This will
launch a wizard that allows you to partition the drive, format it, and
assign it a drive letter.
Page 6
REMEMBER,
!
ARNING
www.CRU-DataPort.com

Setting up the Drive for Macs

W
Formatting your drive will result in loss of data.
1.
After connecting the DataPort HotDock to your Mac, you should
see a new disk added to your desktop. If the drive is not correctly
formatted you will be asked to initialize it.
2.
To initialize the drive, click the partition tab and set your desired
partitions and then click OK. The new disk will be added to your
REMEMBER, formatting your drive will result in loss of
desktop.
data.

Removing the Hard Disk Drive

Win 98SE, ME, 2K and XP
1.
Right-click on the green arrow icon in the system tray and select
Remove/Reject.
2.
Highlight the Mass Storage Device in the dialog box and then click
Stop.
3.
Choose the external disk drive that you want to disconnect and
then click Stop.
4.
Wait until the "You may safely remove this device" message
displays. Unplug the cable from the computer.
W
If your computer reports that the drive is busy, you
must shut down your computer and then remove the
drive. Failure to do so may result in data loss or
corruption.
Mac OS 9.7/X
1.
When you disconnect the External drive from the Mac, close all
windows and quit all applications that are running on the external
drive.
2.
Drag the external drive icon into Trash to dismount it from the
desktop prior to unplugging the drive.

Troubleshooting

•
Drivers – For the DataPort HotDock to be properly recognized,
your computer needs to have the latest available driver updates
provided by the manufacturer of your software and hardware.
www.CRU-DataPort.com
!
ARNING
!
ARNING
Page 7