Whirlpool 9830492 Инструкции по установке - Страница 4

Просмотреть онлайн или скачать pdf Инструкции по установке для Сушилка Whirlpool 9830492. Whirlpool 9830492 5 страниц. Compact dryer

Печатать страницу

Now stand the dryer up.

Mobile home exhaust

requirements:

The dryer

must

have an outside

exhaust.

If the

dryer is exhausted

through

the

floor and the area under the

ide

Use duct tape

to seal all joints.

Four-inch rigid metal pipe

preferred.

Plan installation

use the fewest number

of elbows

and turns

better

i==l

mobile

home is enclosed,

the

exhaust

system

must

terminate

outside the enclosed

area.

Extension beyond

the

enclosure

wili prevent

lint and

moisture

buildup

under the mobile

home.

Metal flexible duct

must be fully extended

and supported

when the dryer is in its final

position.

DO NOT KINK OR CRUSH THE DUCT.

The metal flexible

duct must be completely

open to allow adequate

exhaust

air to flow.

Allow as much room as possible when using

elbows or making

turns. Bend duct gradually

to avoid

kinking. Remove

excess flexible

duct to avoid sagging

and

kinking that may result in

reduced

air flow.

Exhaust Outlet

is located

the center

of the bottom

dryer back.

The

exhaust duct

can be

routed

up, down,

left, right

or straight out the back of

the dryer. Detailed

space

requirements

are provided

on the back cover of

Installation

Instructions.

Maximum length

of the exhaust

system

depends

upon the type of duct used,

number

of elbows and the type of exhaust

hood. The maximum

length for both rigid

and flexible

duct is shown in chart.

Move the drver to its oermanent

Now start...

with dryer in laundry

area.

location.

Remove

cardboard

'or hardboard

from under dryer. Check

levelness

of dryer

by placing

level on top of the dryer, first side

to side, then front to back.

If dryer is not

level, adjust the legs of the dryer up or down

until dryer is level.

Remove

the tape that holds the

drum to the cabinet.

(Some dryer drums are

not taped

for shipping.)

Move the drum by

hand to make certain

all tape

has been

removed.

Wipe the interior of the drum

thoroughly

with a damp

cloth before

using

the dryer. Remove

tape from lint screen.

To exhaust

the dryer, see Exhaust

requirements.

Connect

exhaust

duct to

exhaust

hood. Use duct tape to seal all joints

in exhaust

duct. Use caulking

compound

seal exterior wall opening

around

exhaust

hood.

Carefully

push

timer knob on the

timer shaft at the front

of the dryer.

I HOOD TY

EXHA

A3 Fr.

33 Fr.

23 Fr

30 Fr.

2AFT.

16FI.

Take two of the cardboard

corners

NUMBER OF

90" TURNS

from the carton

and place

them on the floor

to the right side of the dryer.

Stand in front of dryer. Firmlv grasp

the body of the dryer and gently

lay

ti right

side down

on the cardboard

corners.

timer knob

Check

to see that all of the parts you

Al FI.

31 FT.

21 Fr

removed

from the installation

parts

packages

are now

installed

in the dryer. If

you still have an extra part, go back through

the steps to see what you skipped.

Check

make sure you have all the tools you started

29 FT.

23 FT.

15 FT.

with.

Plug the

electrical

cord into

the grounded

outlet.

Start to

screw the legs into

the holes bv hand.

For exhaust systems

not covered

by the

exhaust

length chart, check

with your dealer

or distributor

for information.

Service check:

The back pressure in any

exhaust

system used must not exceed

0.3

inches of water column

measured

with an

inclined

manometer

at the point that the

exhaust

duct connects

to the dryer.

Exhausting the dryer outside

recommended.

A closet installation

must

exhausted

outside.

Recessed

installation

that is not exhausted

outside must use

Exhaust Deflector

Part No. 603197 available

from your dealer.

See "Recessed

and closet

installation

instructions"

on back cover for

adequate

unobstructed

air opening

requirements.

If the dryer is installed in a confined area

such as a bedroom, bathroom, or closet,

must be exhausted

to the outside and

provision

must be made

for enough

air for

combustion

and ventilation.

Check

governing

codes and ordinances.

Also refer

to the "Recessed

and closet installation

instructions"

on back cover.

exhaust hood

should cap

the exhaust

duct to prevent

exhausted

air from returning

into dryer. The outlet of the

hood must be at least 12"

from the ground

or any

object

that may be in the

path of the exhaust.

Four-inch outlet exhaust

hood

is preferred.

However,

a 2-l/2-inch

outlet exhaust

hood may be

used. A 2-l/2-inch

outlet exhaust

hood

creates

greater

back pressure than other

hood types.

For permanent installation, a stationary

exhaust system is required.

Mobile home installation

This appliance

is suitable

for mobile

home

installations.

The installation

of the dryer must

conform

to the Manufactured

Home

Construction

and Safety Standard,

Title 24

CFR, Part 3280 (formerly

the Federal

Standard

for Mobile

Homes Construction

and Safety, Title 24, HUD Part 280, 1975) or

the latest edition.

Use a small'amount

of liquid detergent

lubricate

the screw so it is easier to turn the

leg. Use an adjustable

wrench

to finish

turning the legs until you have

1" of the leg

below the base.

Read the Use and Care Guide to

fully understand

you new dryer. Start the

dryer. Start the dryer and allow it to

complete

a regular cycle.

After five minutes,

open dryer door and check

that dryer is

operating

properly.

To get the most efficient use from

your new dryer, read your Use

and Care Guide. Keep Installation

Instructions and Guide close to

the dryer for easy reference.

Floor Damage

Slide dryer onto cardboard

or hardboard

before moving across floor.

Failure to do so may cause damage to

floor covering.

Numbers

correspond to

steps.

Panel C