Whirlpool 9830492 Kurulum Talimatları - Sayfa 4
Kurutucu Whirlpool 9830492 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Whirlpool 9830492 5 sayfaları. Compact dryer
5
n
Now stand the dryer up.
Mobile home exhaust
requirements:
The dryer
must
have an outside
exhaust.
If the
dryer is exhausted
through
the
floor and the area under the
ide
Use duct tape
to seal all joints.
Four-inch rigid metal pipe
is
preferred.
Plan installation
to
use the fewest number
of elbows
and turns
better
n
i==l
mobile
home is enclosed,
the
exhaust
system
must
terminate
outside the enclosed
area.
Extension beyond
the
re
enclosure
wili prevent
lint and
moisture
buildup
under the mobile
home.
Metal flexible duct
must be fully extended
and supported
when the dryer is in its final
position.
DO NOT KINK OR CRUSH THE DUCT.
The metal flexible
duct must be completely
open to allow adequate
exhaust
air to flow.
Allow as much room as possible when using
elbows or making
turns. Bend duct gradually
to avoid
kinking. Remove
excess flexible
duct to avoid sagging
and
kinking that may result in
reduced
air flow.
Exhaust Outlet
is located
at
the center
of the bottom
dryer back.
The
exhaust duct
can be
routed
up, down,
left, right
or straight out the back of
the dryer. Detailed
space
requirements
are provided
on the back cover of
Installation
Instructions.
Maximum length
of the exhaust
system
depends
upon the type of duct used,
number
of elbows and the type of exhaust
hood. The maximum
length for both rigid
and flexible
duct is shown in chart.
6
n
Move the drver to its oermanent
Now start...
with dryer in laundry
area.
location.
Remove
cardboard
'or hardboard
from under dryer. Check
levelness
of dryer
by placing
level on top of the dryer, first side
to side, then front to back.
If dryer is not
level, adjust the legs of the dryer up or down
until dryer is level.
1
n
Remove
the tape that holds the
drum to the cabinet.
(Some dryer drums are
not taped
for shipping.)
Move the drum by
hand to make certain
all tape
has been
removed.
Wipe the interior of the drum
thoroughly
with a damp
cloth before
using
the dryer. Remove
tape from lint screen.
7
1
n
To exhaust
the dryer, see Exhaust
requirements.
Connect
exhaust
duct to
exhaust
hood. Use duct tape to seal all joints
in exhaust
duct. Use caulking
compound
to
seal exterior wall opening
around
exhaust
hood.
&
8
n
Carefully
push
7
timer knob on the
"
timer shaft at the front
I
of the dryer.
l-
I HOOD TY
EXHA
A3 Fr.
33 Fr.
23 Fr
30 Fr.
2AFT.
16FI.
2
n
Take two of the cardboard
corners
NUMBER OF
90" TURNS
from the carton
and place
them on the floor
to the right side of the dryer.
3
n
Stand in front of dryer. Firmlv grasp
the body of the dryer and gently
lay
ti right
side down
on the cardboard
corners.
timer knob
9
n
Check
to see that all of the parts you
Al FI.
31 FT.
21 Fr
removed
from the installation
parts
packages
are now
installed
in the dryer. If
you still have an extra part, go back through
the steps to see what you skipped.
Check
to
make sure you have all the tools you started
29 FT.
23 FT.
15 FT.
with.
10
n
Plug the
electrical
cord into
the grounded
outlet.
4
n
Start to
screw the legs into
the holes bv hand.
For exhaust systems
not covered
by the
exhaust
length chart, check
with your dealer
or distributor
for information.
Service check:
The back pressure in any
exhaust
system used must not exceed
0.3
inches of water column
measured
with an
inclined
manometer
at the point that the
exhaust
duct connects
to the dryer.
Exhausting the dryer outside
is
recommended.
A closet installation
must
be
exhausted
outside.
Recessed
installation
that is not exhausted
outside must use
Exhaust Deflector
Part No. 603197 available
from your dealer.
See "Recessed
and closet
installation
instructions"
on back cover for
adequate
unobstructed
air opening
requirements.
If the dryer is installed in a confined area
such as a bedroom, bathroom, or closet,
it
must be exhausted
to the outside and
provision
must be made
for enough
air for
combustion
and ventilation.
Check
governing
codes and ordinances.
Also refer
to the "Recessed
and closet installation
instructions"
on back cover.
An
exhaust hood
should cap
the exhaust
duct to prevent
exhausted
air from returning
into dryer. The outlet of the
hood must be at least 12"
from the ground
or any
object
that may be in the
path of the exhaust.
Four-inch outlet exhaust
3L
hood
is preferred.
However,
a 2-l/2-inch
outlet exhaust
hood may be
used. A 2-l/2-inch
outlet exhaust
hood
creates
greater
back pressure than other
hood types.
For permanent installation, a stationary
exhaust system is required.
Mobile home installation
This appliance
is suitable
for mobile
home
installations.
The installation
of the dryer must
conform
to the Manufactured
Home
Construction
and Safety Standard,
Title 24
CFR, Part 3280 (formerly
the Federal
Standard
for Mobile
Homes Construction
and Safety, Title 24, HUD Part 280, 1975) or
the latest edition.
Use a small'amount
of liquid detergent
to
lubricate
the screw so it is easier to turn the
leg. Use an adjustable
wrench
to finish
turning the legs until you have
1" of the leg
below the base.
11
n
Read the Use and Care Guide to
fully understand
you new dryer. Start the
dryer. Start the dryer and allow it to
complete
a regular cycle.
After five minutes,
open dryer door and check
that dryer is
operating
properly.
To get the most efficient use from
your new dryer, read your Use
and Care Guide. Keep Installation
Instructions and Guide close to
the dryer for easy reference.
Floor Damage
Slide dryer onto cardboard
or hardboard
before moving across floor.
Failure to do so may cause damage to
floor covering.
J
8.
6.
0
_
3
I
Numbers
correspond to
steps.
Panel C