dixell COOL MATE XLH360 Руководство по эксплуатации - Страница 9

Просмотреть онлайн или скачать pdf Руководство по эксплуатации для Контроллер температуры dixell COOL MATE XLH360. dixell COOL MATE XLH360 16 страниц. Cool mate temperature and humidity controller for seasoning-maturing cabinets

Печатать страницу

dIXEL

trC=cLE at the end of the stopping phase the regulation restarts from the running phase.

DEFROST

tdF

Defrost type: rE = electrical heater (Compressor OFF); in = hot gas (Compressor and defrost relays ON)

EdF

Defrost mode:

in = interval mode. The defrost starts when the time "Idf" is expired; Sd=Smartfrost mode. The IdF time (interval

between defrosts) is increased only when the compressor is running (even non consecutively).

SdF

Set point for SMARTFROST: (-30

SMARTFROST mode.

dtE

Defrost termination temperature: (-50,0÷110,0°C; -58÷230°F) (Enabled only when the evaporator probe is present) sets the

temperature measured by the evaporator probe which causes the end of defrost.

IdF

Interval between defrosts: (1÷120h) Determines the time interval between the beginning of two defrost cycles.

MdF

Duration of defrost: (0÷255 min) When P2P = n, no evaporator probe, it sets the defrost duration, when P2P = y, defrost end based on

temperature, it sets the maximum length for defrost.

dFd

Display during defrost: rt = real temperature; it = temperature reading at the defrost start;

Set

set point; dEF = "dEF" label; dEG = "dEG" label;

dAd

Defrost display time out: (0

255 min) Sets the maximum time between the end of defrost and the restarting of the real room temperature

display.

Fdt

Drain down time: (0÷60 min.) time interval between reaching defrost termination temperature and the restoring of the control's normal

operation. This time allows the evaporator to eliminate water drops that might have formed due to defrost.

dPO

First defrost after start-up: y = Immediately; n = after the IdF time

Hud

Humidity control during defrost: no: the humidity control is stopped during the defrost; yES the humidity control works also during the

defrost.

FANS

FnC

Fan operating mode: C-n = running when a load is on, OFF during the defrost; C-y = running when a load is on, ON during the defrost;

O-n = continuous mode, OFF during the defrost; O-y = continuous mode, ON during the defrost;

EXTRACTOR FANS

rFi

Interval between 2 cycles of change of air (0÷120 ore; 0 = only manual starting)

rFd

Duration of change of air cycle (0÷250min; 0 = only manual stopping)

TEMPERATURE ALARMS

ALC

Temperature alarm configuration: rE = High and Low alarms related to Set Point; Ab = High and low alarms related to the absolute

temperature.

ALL

Low temperature alarm setting: ALC = rE , 0

and after the ALd delay time, the LA alarm is enabled,.

ALU

High temperature alarm setting: ALC= rE, 0

after the ALd delay time the HA alarm is enabled.

ALH

Temperature alarm recovery differential: (0,1÷25,5°C; 1÷45°F) Intervention differential for recovery of temperature alarm.

ALd

Temperature alarm delay: (0÷255 min) time interval between the detection of an alarm condition and the corresponding alarm signalling.

dAO

Delay of temperature alarm at start-up: (0min÷23h 50min) time interval between the detection of the temperature alarm condition after

the instrument power on and the alarm signalling.

EdA

Alarm delay at the end of defrost: (0

defrost and the alarm signalling.

dot

Delay of temperature alarm after closing the door : (0

door.

HUMIDITY ALARMS

AHC

Humidity alarm configuration: rE = High and Low alarms related to humidity Set Point ; Ab= High and low alarms related to the

"absolute" humidity.

AHL

Low humidity alarm setting: (with AHC = rE: 0 ÷ 50. With AHC = Ab: Lci ÷ AHu)

when this humidity is reached and after the AHd delay time, the HLA alarm is enabled,.

AHu

High humidity alarm setting: (with AHC = rE: 0÷50°C. with AHC = Ab: AHL ÷ uci

when this humidity is reached and after the AHd delay time the HHA alarm is enabled.

AHH

Humidity alarm recovery differential: (0.5÷20.0) Intervention differential for recovery of humidity alarm.

AHd

Humidity alarm delay: (0÷255 min) time interval between the detection of an alarm condition and the corresponding alarm signalling.

dHo

Delay of humidity alarm at start-up: (0min÷23h 50min) time interval between the detection of the humidity alarm condition after the

instrument power on and the alarm signalling.

doH

Alarm delay at the end of defrost: (0

and the alarm signalling.

doA

Open door alarm delay:(0÷255 min) delay between the detection of the open door condition and its alarm signalling: the flashing

message "dA" is displayed.

tbA

Alarm relay status after pushing a key: on= the relay remains on; off= the relay is switched off.

nPS

Pressure switch number: (0

15) Number of activation of the pressure switch, during the "did" interval, before signalling the alarm event

(I1F= PAL). If the nPS activation in the "did" time is reached, switch off and on the instrument to restart normal regulation.

1592017410 XLH360 GB r1.0 15.04.2005.doc

Operating Instructions

30 °C/ -22

86 °F) evaporator temperature which allows the IdF counting (interval between defrosts) in

50 °C or 90°F; ALC = Ab , - 50°C or -58°F

50°C or 90°F; ALC= Ab, ALL

255 min) Time interval between the detection of the temperature alarm condition at the end of

255 min) Time delay to signal the temperature alarm condition after closing the

255 min) Time interval between the detection of the humidity alarm condition at the end of defrost

XLH360

cod. 1592017410

ALU; when this temperature is reached

110°C or 230°F; when this temperature is reached and

9/16