AME MM-1 Kurulum Kılavuzu - Sayfa 2
Araba Alarmı AME MM-1 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. AME MM-1 6 sayfaları.
Ayrıca AME MM-1 için: Kullanıcı Kılavuzu (15 sayfalar), Kurulum Kılavuzu (14 sayfalar)
Sayfayı YazdırFunction programming.
1. Follow through with transmitter programming and turn the ignition back on (before the double siren beep in the
above item 3!).
2. Press button 1 on the transmitter 12 times. The alarm system will provide an audible confirmation on each
pressing the button. When you are pressing the button the 12th time the siren will emit two long beeps
followed by two short beeps.
3. Press buttons 1 and 2 together to enter the Installer Software Switch Table.
4. Enter the number of the function that you want to adjust by pressing button one on the transmitter to increase
the number of function or by pressing button 2 to reduce the number of function.
5. Each time the transmitter button is pressed; the siren will beep to indicate the switch that is selected. The
following siren beep sequence will be used: Switch 1 = One short beep, Switch 2 = Two short beeps, ...
Switch 5 = One long beep, Switch 6 = One long beep and one short beep, ... and so on.
6. Press both buttons 1 and 2 to toggle the status of the dual state functions from option 1 to option 2 and from
option 2 to option 1. If the Software switch includes more than two states, follow the instruction within a
respective line of the table below.
7. If option 1 is selected, the LED will be on. If option 2 is selected, the LED will be off.
8. Turn off the ignition and wait 15 seconds. The system will give a double beep to confirm it has exited software
switch adjustment.
Installer Software Switches
Software
Function
Switch
1
Dome Light Cars
2
Door (+/ ) Input Polarity
3
CDL Locking Time
4***
Twenty Second Locking
5*
Shock Sensor Main Trigger Sensitivity
1 = Minimum Sensitivity
10 = Maximum Sensitivity
LED will flash according to the current setting when
the switch is selected.
Press buttons 1 and 2 together to enter the setting.
When required sensitivity is set press buttons 1 and 2
once again to confirm and exit the setting.
Shock Sensor will be in a test mode when this
switch is selected to allow testing sensitivity.
6*
Shock Sensor Pre Warn Trigger Sensitivity
1 = Minimum Sensitivity
10 = Maximum Sensitivity
LED will flash according to the current setting when
the switch is selected.
Press buttons 1 and 2 together to enter the setting.
When required sensitivity is set press buttons 1 and 2
once again to confirm and exit the setting.
Shock Sensor will be in a test mode when this
switch is selected to allow testing sensitivity.
7**
Trunk ( )/Pre Warn( ) Input
*NOTE:
WARNING: The Shock Sensor can be adjusted to operate as either one stage or two stage Sensor. To have
one stage Shock Sensor set the same level of sensitivity for both Pre Warn and Main Trigger; for getting two
stage Sensor set the Pre Warn Trigger sensitivity at least one level Higher than Main Trigger sensitivity.
Default Setting
Option 1
Option 2
OFF
ON
OFF
Negative
Positive
Negative
0.8s
0.8s
4s
OFF
ON
OFF
5
Up
Down
(A single beep
(A double beep
will confirm
will confirm
each pressing)
each pressing)
5
Up
Down
(A single beep
(A double beep
will confirm
will confirm
each pressing)
each pressing)
Trunk ( )
Trunk ( )
Pre Warn
Installation manual
AME MM 1 Car Alarm System
2
СХЕМА ПОДКЛЮЧЕНИЙ
Подключение дополнительного двухуровневого датчика
Инструкция по установке
AME MM 1 Автомобильная охранная система
11