Ekinex EK-BW1-TP Hızlı Başlangıç Kılavuzu - Sayfa 3

Ev Otomasyonu Ekinex EK-BW1-TP için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Ekinex EK-BW1-TP 4 sayfaları. Knx voice control interface

Sayfayı Yazdır

Network connection

The configuration and use of the voice control interface

requires a connection to the home or company network.

The default IP address of the interface is: 192.168.0.110.

For the initial configuration of the interface, as well as in

case of absence of a network during the installation pha-

se, it is necessary to proceed as follows:

1. connect the interface to your PC via a "cross over" (or

"crossover") network cable

2. access your PC's network settings, as illustrated in

your operating system documentation

3. Change the TCP/IP communication protocol settings

(version 4) for the LAN port of your PC, and set the

following parameters manually:

• IP address: 192.16 8.0.100

• Network mask: 255.255.255.0

• Default gateway: 192.168.0.110

• Save and wait for the new settings to take effect. If

prompted, reboot the system.

After these operations, open an Internet browser and

type in the address bar:

http://192.168.0.110

Note! For an optimal browsing experience, we recommend using

one of the following browsers:

• Google Chrome

• Apple Safari

First access

When you open the browser at the default address, the

the voice control interface has the following preset user

at the factory:

User

admin

Enter the credentials of the user "admin" and confirm to

access the main screen of the voice interface administra-

tion environment.

Restore factory IP address

If necessary, you can restore the factory IP address of the

voice interface using the RESET button available. Follow

the procedure below:

• open the front panel of the device using a small slotted

screwdriver, and exerting a slight leverage effect in one

of the side slots

• locate the RESET button on the back of the vertical

card

• Press the button for at least 10 seconds until the SER-

VICE LED on the front of the device starts flashing,

then release the button.

• within the next 5 seconds, press and release the button

for 1 second; within a couple of seconds the front LED

will light up solidly for a couple of seconds

• When the LED goes out, the device can be reached at

the factory IP address (192.168.0.110).

If the LED goes out after long press (10 seconds) before

short press, repeat the whole procedure. This procedure

resets the IP address and retains all data relating to the

configuration previously carried out on the automation sy-

stem.

Restore factory configuration

If the configuration made makes it impossible to access

the server delégo or its correct use, it is possible to re-

store the factory conditions, resetting the IP address and

emptying the supervision project using the "RESET" but-

ton available. In this case, compared to what was pre-

viously seen to restore the IP address, the procedure to

follow is the following:

• open the front panel of the device using a small slotted

• locate the RESET button on the back of the vertical

• Press the RESET button for at least 10 seconds un-

• within the next 5 seconds, press and hold the button for

• When the LED is solidly lit, release the button and wait

• when the LED goes off, remove and restore the power

• Wait about one minute and log in to the server with the

Warning! To avoid losing all the configurations made for the au-

tomation project during a factory reset operation, it is recommen-

ded to make periodic backups of the supervision project.

The configuration and commissioning activities of the KNX voice

control interface require specialized skills on the KNX network

and knowledge of the specific automation project carried out with

ETS. To acquire these skills, it is essential to participate in the

courses organized at KNX certified training centers. For further

information: www.knx.it

Password

admin

Dimensions [mm]

Approvals

• CE the products complie with the Low Voltage Directive

Maintenance

The devices are maintenance-free. To clean them, use

a dry cloth. The use of solvents or other aggressive sub-

stances is absolutely to be avoided.

screwdriver, and exerting a slight leverage effect in one

of the side slots

card

til the SERVICE LED on the front of the device starts

flashing, then release the button.

at least 10 seconds

for it to go out.

supply

factory IP address (192.168.0.110).

EK-BW1-TP

Voice control

(2014/35 / EU) and the Electromagnetic Compatibility

Directive (2014/30 / EU). Tests carried out in accordan-

ce with EN 50491-5-1: 2010, EN 50491-5-2: 2010.