Door-Gard 2000eM Kurulum ve Programlama - Sayfa 6

Tuş takımı Door-Gard 2000eM için çevrimiçi göz atın veya pdf Kurulum ve Programlama indirin. Door-Gard 2000eM 7 sayfaları.

Sayfayı Yazdır

Programming Keypad Parameters

(Default settings are in bold)

Command/Action

Change Keypad Parameters

Parameter

0 – Duress Output Duration

1 – Panic Output Duration*

2 – Error Lockout Threshold

3 – Error Lockout Duration

4 – Auto-Entry Count

7 – Auto-Entry Keypress

Timeout

10 – Wiegand Format

11 – Wiegand Pulse Width

12 – Wiegand Interpulse

Spacing

Note: Refer to the Wiegand Format Chart for parameter 8.

Change Wiegand Parameters

Parameter

0 – Wiegand Site ID

1 – Wiegand Group ID

Note: The default setting for both settings is 0.

*Note: The Panic Output is activated by pressing the ✱ and # keys

at the same time. This is used in case of emergency to activate an

auxiliary alarm device, such as a siren, that is used to indicate an

emergency condition only. This output should not be used to gain

access. All access control functionality should be programmed and

remain separate from the Panic Output functionality.

Resetting the Keypad

Note: This does not reset the keypad operating mode.

Command/Action

Reset Defaults Only

Reset Entire Keypad

Keys to Enter/Details

32 # parameter # value # ✱ ✱

Value

1 – 255 Seconds (default = 5)

1 – 50 Attempts (default = 3)

1 – 255 Seconds (default = 10)

2 – 10 Digits (default = 4)

2 – 15 Seconds (default = 2)

1 – 8 (default = 1, 26-Bit)

1 – 255 (default = 8, 160μS)

1 – 255 (default = 32, 640μS)

34 # parameter # value # ✱ ✱

Value

Refer to Wiegand Format Chart

Keys to Enter/Details

40 # 00000 # 00000 # ✱ ✱

46 # 00000 # 00000 # ✱ ✱

2000e & 2000eM Keypad Installation & Programming

Wiegand Format Chart

The keypad supports the following Wiegand formats (parameter 10).

Format

Wiegand

Value

Format

26 bit

28 bit

29 bit

30 bit

31 bit

32 bit

36 bit

29 bit

Wiegand Data

When the keypad is conﬁ gured in Wiegand mode, the keypad data is

sent as a complete Wiegand data packet, as though you presented a

card.

For example, when programming a user into an Door Control Module,

you must program the user as though you were programming a card.

After entering the command to program a card user, enter the code

on the 2000e/eM keypad to send the data to the controller.

Please refer to the Wiegand Interface Module instructions 6-065700,

the HubMax II Instructions 6-065034 and the Hub MiniMax II

instructions 6-055037 for complete details.

LED/Sounder Indications

Indicator

Steady Red*

Steady Green*

Yellow Flashing Slowly

Solid Yellow

Alternating Red/Green

LED's Cycling Left to Right

LED's Cycling Right to Left

3 Rapid Beeps

Pair of Double Beeps

Single Double Beep

1 Long Beep, 1 Short Beep

1 Long Beep, 3 Short Beeps

1 Long Beep, 5 Short Beeps

6 Quick Beeps

Sounder ¼ sec on, ¼ sec off

Beep Every 2 seconds

*Note: The Red/Green LED descriptions above are for Standalone

and Secured Series Mode only. The operation of these LED's in

Wiegand Mode is determined by the LED control wire (brown) and

how it is conﬁ gured. The LED control is conﬁ gured using keypad

Options 19, 20, 21 and 22, which are programmed with Command 30.

Largest

PIN Value

Site Value

65535

255

32767

255

524287

255

65535

255

65535

255

8191

2047

999999

1023

524287

255

Description

Door Locked

Door Unlocked (timed or latched)

Program Mode

Program Error or Error Lockout

Awaiting 2nd PIN of Two-Part User

Over Voltage Warning

Under Voltage Warning

Invalid Code

User Lockout Activated

User Lockout Canceled

Access Denied, User Disabled

Access Denied, User Lockout

Access Denied, Code Mismatch

Toggle Mode Activated

Audio Alert 1

Audio Alert 2

6-104402 X2

Largest

Group

Value

N/A