Dover TWG TULSA WINCH 506W Servis Kılavuzu - Sayfa 9
Vinçler Dover TWG TULSA WINCH 506W için çevrimiçi göz atın veya pdf Servis Kılavuzu indirin. Dover TWG TULSA WINCH 506W 18 sayfaları.
Sayfayı Yazdır
1. Thoroughly clean all parts. Replace those that show wear or damage.
(Item 5)
2. Inspect the drum
replace if necessary.
3. Attach the output shaft
making sure the vent
Torque Specifications Chart on page 15 of this manual)
4. Install the retaining ring
(Item 43)
5. Attach the rods
(Items 2 & 60)
. Torque to specification
manual)
.
6. If necessary, install a new bearing
7. Lay the unit down so that the rods
(Item 5)
onto the output shaft
8. Install the planet gearset
(Item 32)
onto the shaft
(Item 8)
9. Insert the sun gear
installed down, facing the output shaft.
(Item 7-4)
10. Install a new o-ring
into the bearing carrier
the drum.
11. Position the side plate
plate with eight capscrews
Chart on page 15 of this manual).
12. Install the brake subassembly into the side plate
(Item 21)
brake housing
(Item 26)
carrier
and that the holes for the motor are in the correct orientation. Also, make
sure that the level and vent plugs in the cover are properly oriented. Install one capscrew
9)
(Item 65)
and five nuts
page 15 of this manual
(Item 7-2)
13. Install a new o-ring
valve assembly. Install two capscrews
(see Torque Specifications Chart on page 15 of this manual)
specification
(Item 46)
14. Reconnect the tube
15. Fill both the gearbox and the brake section with the proper amount and type of lubricants as
Recommended Oil
instructed in the
ASSEMBLY
for structural integrity and the gear teeth for excessive wear, then
(Item 32)
to the side plate
(Item 30)
is oriented properly, then torque them to specification
(Item 3)
onto the output shaft
(Item 12)
and base
(see Torque Specifications Chart on page 15 of this
(Item 28)
and oil seal
(Item 43)
and base
(Item 32)
being careful not to damage the seal
(Item 4)
into the drum
.
into the planet gearset
and, if necessary, a new bearing
(Item 26)
. Grease the o-ring and seal and install the bearing carrier into
(Item 1)
on top of the rods
(Items 2 & 60)
. Torque to specification
aligns with the bearing
and torque them to specification (
).
on the face of the motor and re-install the motor/counterbalance
(Item 51)
to the brake housing
section on page 6 of this manual.
9
(Item 50)
with six capscrews
.
(Item 32)
.
(Item 50)
to the side plate
(Item 7-8)
into the drum.
(Item 12)
are pointing up. Set the drum
(Item 5)
, making sure it's installed correctly
(Item 4)
. The slot in the sun gear must be
(Item 28)
(Item 43)
and base
(Item 12).
(see Torque Specifications
(Item 1)
, making sure that the pilot of the
(Item 28)
(Item 7-8)
and seal
see Torque Specifications Chart on
(Item 52)
and washers
(Item 21).
(Item 62)
,
(see
with eight capscrews
(Item 7-8)
.
(Item 7-8)
and seal
Attach the side
in the bearing
(Item
and torque them to
.