Draper Premier Kurulum ve Kullanım Talimatları
Projeksiyon Perdesi Draper Premier için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Talimatları indirin. Draper Premier 2 sayfaları. 220v premier electric projection screen
Ayrıca Draper Premier için: Kurulum ve Kullanım Talimatları (2 sayfalar), Kurulum Talimatları (2 sayfalar), Talimatlar Kurulum ve Çalıştırma (7 sayfalar), Kurulum Talimatları (4 sayfalar), Kurulum Talimatları (2 sayfalar), Kurulum Talimatları (2 sayfalar), Kurulum ve Kullanım Talimatları (4 sayfalar), Kurulum ve Kullanım Talimatları Kılavuzu (7 sayfalar)
Sayfayı Yazdır
Targa and Premier Electric Projection Screens—Large Sizes by Draper
➀ Read instructions through completely before proceeding.
➁ Follow instructions carefully. Installation con trary to instructions in val i dates
warranty.
➂ Screen should be accessible for complete removal should fabric be come
damaged or should other ser vice be required.
➃ Screen should be installed level (using a carpenter's level). The case must
also be installed so that the top of the case is level (front-to-back) to prevent
the fabric from contacting the case housing.
➄ Nothing should be fastened to screen dowel or viewing surface.
➅ Operating switch(es) packed separately in screen carton. Do not dis card
with packing material.
➆ Screen operates on 110-120V, 60 hz. current.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
These instructions are meant as a guide only. They do not imply any re spon si bil i ty on
the part of Draper, Inc. for improper in stal la tion or faulty work man ship at the jobsite.
Hanging Screen
General:
Screen should be lifted into position only by the end mounting brackets.
Never attempt to lift screen along its length.
Installer must also insure that wall or ceiling structure is of adequate
strength. Supporting hardware must be essentially vertical. Do not suspend this
product using chain or cable (see note at bottom right regarding this screen
with Tork Star). The screen must be securely fastened using at least two of the
mounting holes provided in each of the case mounting brackets.
When locating view ing surface and checking clear ance for screen's op er a tion,
remember surface is centered in case. Handle case care ful ly to protect its fi nish.
Regardless of mounting method, screen should be positively and securely
sup port ed so that vibration or even abusive pulling on the viewing surface will not
cause case to work loose or fall. Installer must insure that fas ten ers used are of
adequate strength and suit able for the mounting sur face cho sen.
Ceiling Installation:
Product is very heavy: Installer must provide adequate attachment hardware
and anchors as required. Installer must also insure that ceiling structure is of
adequate strength.
Wall Installation:
Product is very heavy: Installer must provide adequate attachment hardware
and anchors as required. Installer must also insure that wall structure is of
adequate strength.
Caution: Do not remove the roller assembly from the case unless neces-
sary for repairs. If the roller assembly is removed, be sure motor is fully
re-seated in the bracket, and re-secure it carefully with the motor retaining
spring and screw (see diagram below).
Screw is included
with Large Targas
and Large Premiers.
Please note: Do not use a power screwdriver to tighten screw.
Maximum torque for tightening screw is 5 lb-inches.
Electrical Connections
Screen operates on 110-120V, 60 Hz. current. Screen is shipped with internal
wiring complete and control switch(es) fully boxed, and standardly supplied with a 6'
cable lead. Longer lead can be substituted by removing two screws in motor end of
roller, removing lead, plugging new lead in, and replacing screws. Wire to connect
screen to switch(es) and switch(es) to power supply should be fur nished by installer.
Con nec tions should be made in ac cor dance with attached wiring diagram, and
wiring should comply with national and local electrical codes.
All operating switches should be "off" before power is connected.
®
Copyright © 2009 Draper Inc. Form Targa_Premier-LargeSizes_Inst09-R2 Printed in U.S.A.
Installation/Operating Instructions
Caution
Before fully operating screen: On Large Targa, remove tape; on Large Premier,
lower viewing surface enough to fully expose shipping brackets, then remove ship-
ping brackets by loosening screws, removing end shipping brackets, sliding center
shipping brackets off dowel, and re-tightening screws (see diagram).
110-120V Single Station Control — 3-position up-off-down switch per mits op er a-
tion to be stopped at any point. Factory adjusted limit switch es au to mat i cal ly stop
screen when fully down or fully up.
110-120V Multiple Station Control — Switches are similar in ap pear ance to
110-120V Single Station Control. Screen stops when switch is re leased and may be
re start ed in either direction. Factory adjusted limit switch es stop screen automati-
cally when fully up or fully down.
24V Control — Three-button up-stop-down switch es stop at any point de sired,
operate in any sequence. Factory adjusted limit switches au to mat i cal ly stop screen
when fully up or fully down.
Key Operated Switching — Two kinds of key-operated switches are op tion al ly
available with this unit. ➀ The key-operated power sup ply switch controls power to
the screen and switches. When it is "off ", the switch es will not operate screen. Key
may be re moved from the switch in either "on" or "off" position.
key switch per mits the screen to be operated directly by key. In this case, the
screen's operator must always have a key.
RS232/Ethernet — Serial communication and network communication optionally
available with wall switches, RF or IR remote.
Adjustments
Screen has been factory set and should not nor mal ly require further ad just ment.
However, if you desire to change the "up" and "down" stop ping po si tions, proceed
as follows:
CAUTION: Be sure all switches are in "off " position before ad just ing limit switch-
es. Always be pre pared to shut screen off man u al ly when new adjust- ment is being
tested. Screen may be se vere ly dam aged if viewing surface is al lowed to run too far
up or too far down.
Adjusting "fully up" position —You should never have to adjust this limit! If
you do, however, the "Up" stopping position may be ad just ed by turning the yellow
limit switch adjustment socket. The yellow socket is lo cat ed on left end of screen
roller and is accessible to a screwdriver/Allen wrench (4mm or
socket coun ter clock wise will allow the view ing surface to retract farther into the
case. Turn ing it clockwise will cause the sur face to stop farther out of the case. One
full revolution of the socket will alter the stop ping position of the view ing surface by
ap prox i mate ly 1½".
Adjusting "fully down" position — "Down" stopping position may be adjusted
by turning the white limit switch adjustment socket. The white socket is located on
the left end of screen roller and is accessible to a screw driv er/Allen wrench (4mm
or
5
/
"). Turning the socket coun ter clock wise will allow the viewing surface to run
32
farther down. Turning it clockwise will shorten the viewing surface, causing it to stop
in a less extended po si tion. At no time should viewing surface be unrolled enough to
expose any part of screen roller.
6
5
/
"
8
Targa
Use of Large Case Targa or Large Case Premier screens with TorkStar Utility Li-
neset requires specially modifi ed Large Premier or Large Targa case and mount-
ing brackets. DO NOT use TorkStar with standard Large Case Targa or Premier
screen and brackets. Contact Draper for details.
If you encounter any diffi culties installing or ser vic ing your Targa or Premier screen, call
your dealer or Draper Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.
Operation
➁ A three-po si tion
5
/
"). Turn ing the
32
6
5
/
"
8
Premier
IMPORTANT