Bosch FAP-OC 500Series Kullanım ve Bakım Kılavuzu / Kurulum Talimatları - Sayfa 30

Fırın Bosch FAP-OC 500Series için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu / Kurulum Talimatları indirin. Bosch FAP-OC 500Series 40 sayfaları. Built-in wall ovens
Ayrıca Bosch FAP-OC 500Series için: Kurulum Talimatları Kılavuzu (21 sayfalar), Kullanım Kılavuzu (40 sayfalar), Kurulum Kılavuzu (6 sayfalar), Ürün Bilgileri (40 sayfalar), Kurulum Kılavuzu (28 sayfalar), Kullanıcı Kılavuzu (48 sayfalar), Kullanıcı Kılavuzu (48 sayfalar), Kurulum Kılavuzu (28 sayfalar), Kullanım ve Bakım Kılavuzu (44 sayfalar), Kurulum Kılavuzu (32 sayfalar), Hızlı Referans Kılavuzu (4 sayfalar), Kullanım ve Bakım Kılavuzu (27 sayfalar), Kurulum Kılavuzu (24 sayfalar), Kurulum Kılavuzu (32 sayfalar), Kullanım ve Bakım Kılavuzu (24 sayfalar), Kurulum Kılavuzu (28 sayfalar), Servis Kılavuzu (41 sayfalar), Kullanım ve Bakım Kılavuzu (21 sayfalar), Kurulum Kılavuzu (32 sayfalar), Servis Kılavuzu (36 sayfalar), Kurulum Kılavuzu (32 sayfalar), Hızlı Başlangıç ve Güvenlik Kılavuzu (13 sayfalar)

Sayfayı Yazdır
Bosch FAP-OC 500Series Kullanım ve Bakım Kılavuzu / Kurulum Talimatları
Clean the strainers at the water tap end of the hose
Remove the hose from the tap.
1.
Rinse the strainer under running water. Look at the
2.
strainer to see if any visible debris is still present.
Rinse again if necessary to remove the debris.
Reconnect the hose to the tap.
3.
Clean the strainers at the washer end of the hose
Remove the hose from the inlet on the back of the
1.
washer.
Using narrow pliers, grasp and pull the strainer from
2.
the inlet port.
Rinse the strainer under running water.
3.
Reconnect the hose to the back of the washer and
4.
turn on the water tap. Check to see if water flows by
starting a warm water wash cycle.
NOTICE: Check for leaks to be sure the rubber washers
are seated at both ends of the water supply hose and the
connections are properly tightened.
30

Cleaning the drain pump

WARNING
9
RISK OF SCALDING
Risk of hot water injury to skin!
Allow the water to cool down prior to actuating the
emergency door lock release.
You are responsible for ensuring all safety
precautions are followed when draining water from
washer and/or manually opening the washer door.
It may be necessary to clean the washer drain pump if
the washer fails to drain (sound of water being pumped
from the washer cannot be heard when the washer
should be draining and other nearby drains, such as a
sink, are draining properly).
The washer pump can become blocked by loose debris
(a good reason to check the drum and remove any
visible debris after each load.) Fabrics that give off large
amounts of fluff may also cause blockage.
To access the washer drain pump, the service cover
must first be removed (see steps below). With the service
cover removed, proceed as follows:
If the washer has not been drained, try to drain it now.
1.
Turn the program selector to the Drain and touch the
Start/Pause button. Wait a few moments to let the
cycle drain the water from the drum. If the pump is
totally blocked, the water will be unable to drain and
the cycle will end.
Shut off the tap so that no more water flows in and has
2.
to be drained.
Switch the appliance off. Unplug the power plug.