Bosch Instructions for Use Kurulum ve Kullanım Talimatları Kılavuzu - Sayfa 19

Kurutucu Bosch Instructions for Use için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Talimatları Kılavuzu indirin. Bosch Instructions for Use 32 sayfaları. 24" compact condensation dryer axxis - white
Ayrıca Bosch Instructions for Use için: Kurulum ve Kullanım Talimatları Kılavuzu (32 sayfalar), Kullanım Kılavuzu (10 sayfalar), Kullanım Kılavuzu (10 sayfalar), Kullanım Kılavuzu (8 sayfalar), Kullanım Kılavuzu (10 sayfalar), Kullanım Kılavuzu (8 sayfalar), Kurulum ve Kullanım Kılavuzu için Talimatlar (8 sayfalar), Kullanım Kılavuzu (8 sayfalar), Kullanım Kılavuzu (8 sayfalar), Kullanım, Bakım ve Kurulum Talimatları Kılavuzu (24 sayfalar), Kullanım Kılavuzu (10 sayfalar), Kullanım Kılavuzu (8 sayfalar), Kullanım, Bakım ve Kurulum Talimatları Kılavuzu (24 sayfalar), Çalıştırma ve Kurulum Talimatları (29 sayfalar), Kullanım Kılavuzu (10 sayfalar), Kullanım Kılavuzu (10 sayfalar), Kurulum Talimatları Kılavuzu (12 sayfalar), Kullanım Kılavuzu (8 sayfalar)

Sayfayı Yazdır
Bosch Instructions for Use Kurulum ve Kullanım Talimatları Kılavuzu

What to do if...

Fault code
Other fault codes are only for use by the after-sales service. Make a note of the fault code to inform the after-
sales service.
Fault
Programme does not start.
The maximum spin speed
cannot be set.
The water is not Drained.
Detergent residues in the
detergent drawer.
Risk of electric shock.
Repairs must only be carried out by customer services or authorised
technicians.
If repairs are needed, or if you cannot rectify a fault yourself with the help
of the following table:
Set the programme selector to Off.
Disconnect the washer-dryer from the power supply.
Turn off the tap.
Call the after-sales service –> page 22.
The door is not properly closed. Close the door.
The water control system has been activated. Disconnect the appliance from
the mains, turn off the tap and advise the after-sales service.
Water is not entering the appliance. See the fault Water is not flowing in.
The water is not Drained. See the fault Water is not Drained.
Maximum or minimum drying load not taken into account. HI/End or LO/End
flash alternately in the display. See information for the Drying result not
satisfactory fault.
Possible cause
The A (Start/Pause) button has not
been pressed.
A delayed start time has been
selected.
Power cut.
The delayed start time that was
selected has been cleared.
The door is not properly closed.
Plug not inserted properly into socket. Insert plug correctly.
The maximum spin speed depends on
the programme selected.
Drain hose is twisted.
Detergent pump is blocked.
Damp or lumpy detergent.
Remedial action
Press the A (Start/Pause) button.
Washer dryer starts on completion of
the delay period.
Change the "finished in time" if
necessary –> page 13.
Reselect the delayed start time or start
the programme immediately.
Press the A (Start/Pause) button.
Close the door.
Change programme as required.
Fit the Drain hose correctly.
Clean the Drain pump –> page 18.
Clean and dry the detergent drawer –
> page 17.
Use the measuring aid for liquid
detergent.
19