Anker 7 Series Kullanıcı Kılavuzu - Sayfa 5

Taşınabilir Jeneratör Anker 7 Series için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Anker 7 Series 12 sayfaları. Portable power station ganprime powerhouse 2048wh
Ayrıca Anker 7 Series için: Kullanıcı Kılavuzu (12 sayfalar), Hızlı Başlangıç Kılavuzu (15 sayfalar)

Sayfayı Yazdır
Anker 7 Series Kullanıcı Kılavuzu

Light

Ambient light
Press the button once to turn on the ambient light, and press again up to 2 times to switch between brightness levels.
SOS Mode
Press and hold the button for 2 seconds to turn on SOS mode.

LCD Screen Guide

13
12
11
10
9
8
Current Output Power
Current Input Power
IoT
Press the IoT button for 2 seconds and connect your devices through the app when this icon appears on the
screen.
Remaining Battery for Expansion Battery
When the expansion battery is connected successfully, this icon appears on the screen.
USB-A Output Port
USB-C Output Port
Car Charging
AC Charge and Voltage Frequency
Low-Temperature Alert
When this icon shows, stop using the power station until the icon disappears.
High-Temperature Alert
10
When this icon shows, stop using the power station and let it cool down until the icon disappears.
11
Overload Warning
This icon appears when a port is overloaded. The port will be turned off to avoid any damage.
Please remove the device causing overload.
12
Estimated Time to Fully Recharge
Estimated Time for Battery to Deplete
13
Remaining Battery for Power Station
14
15
Power Saving Mode
05 EN
x1
x2
x3
SOS
2S
14
15
1
2
7
6
5
4
3

FAQ

Q1: What is the max power output of the AC output ports?
The AC output ports can deliver a maximum of 2400W to connected devices.
Q2: Can Anker 767 Portable Power Station power a CPAP machine?
Yes, but make sure to turn off the Power Saving mode first.
Q3: What should I do when using a solar charger to charge Anker 767 Portable Power Station?
The solar input supports an 11-60V solar charger with an XT-60 connector. If you use an 11-32V solar charger,
the current supports 10A max. When you use a 32-60V solar charger, the current supports 20A max. We
recommend using Anker 531 Solar Panels (200W) to get the best compatibility.
Q4: Can the USB-C ports be used to charge Anker 767 Portable Power Station (input only) or are they output only?
The USB-C ports support output only.
Q5: What should I do when AC recharging fails?
If AC recharging does not work, check to see if the overload protection switch is switched on. If it is on, press
down to reset and then continue recharging.
Q6: How do I reset Anker 767 Portable Power Station?
If your power station isn't working correctly, insert a paper clip or pin into the reset hole for 1 second for a factory
reset. If the power station still doesn't work, please contact [email protected].
Q7: Why is the power station not working after it hasn't been used for a long time?
If the power station is stored at a low capacity for a long time, lithium batteries will self-consume power which
may lead to a quick discharge. This often leads to poor conductivity and a reduced battery lifespan that causes
the battery not to work.
Q8: How should I store and maintain the power station?
When storing your portable power station, please make sure that you:
1) Turn off all the outputs.
2) Store the power station in a dry and cool environment.
3) Check the remaining battery capacity each week. If the battery level is below 30%, fully charge the power
station. Don't forget to charge it to 100% once every 3 months.
EN 06