DSPM UniMeasure HX-VP510 Series Kurulum Kılavuzu

Dönüştürücü DSPM UniMeasure HX-VP510 Series için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. DSPM UniMeasure HX-VP510 Series 3 sayfaları.

Sayfayı Yazdır

HX-VP420 Series Installation Guide

Model HX-VP420

The 4 to 20 mA output transducer is a 2-wire,

loop pow ered de vice. The transducer, pow er

supply, and cur rent monitor must be con nect ed

in series as illustrated above.

The minimum supply voltage is a function of

total loop resistance. It may be calculated us ing

the formula:

V(Min.)= (0.02 x Load Res.) + 9 VDC

It may also be determined from the ac com -

pa ny ing graph, shown at right.

When mounting, insure that the baseplate of the

transducer is grounded to earth ground. For best

noise immunity, use twisted pair

RANGE

Note: Di men sions in

2", 10"

brackets are mil li me ters.

3", 15", 30"

4", 20", 40"

5", 25", 50"

60"

80"

Alternate Wire Rope Exit

Via Paolo Uccello 4 - 20148 Milano

Tel +39 02 48 009 757 Fax +39 02 48 002 070

Wiring and Circuit Diagram

shielded cable between the transducer and the

electrical interface. The shield of the cable

should be open at the transducer and ground ed

at the electrical interface.

With small blade type screwdriver (.105"

max. blade width X .023" max. blade thick-

ness), ad just the Zero and Span con trols on

the trans duc er to set the 4 and 20 mA output

limits. Note: The Zero and Span con trols

are some what in ter ac tive and may re quire

several it er a tions to ob tain the de sired zero

and maxi-

Velocity

The tachometer is self en er giz ing and requires

no input voltage.

Dimensional Information

NOTE

Mount with Ø.25 or M6

Socket Head Cap Screws.

Alternate Wire Rope Exit

"A"

"B"

"C"

1.12 (28.4)

1.79 (45.5)

1.21 (30.7)

.96(24.4)

1.95 (49.5)

1.37 (34.8)

.80 (20.3)

2.11 (53.6)

1.53 (38.9)

.64 (16.3)

2.27 (57.7)

1.69 (42.9)

.49 (12.4)

2.42 (61.5)

1.84 (46.7)

.25 (6.4)

2.66 (67.6)

2.08 (52.8)

mum settings. Ex tend the trans duc er's cable (on

an gu lar position transducers, ro tate shaft) to the

desired zero po si tion (must be with in 0% to 30%

of range). Adjust the Zero con trol so that the

output cur rent is 4 mA. Then extend the ca ble (on

angular position trans duc ers, ro tate shaft) to the

de sired max i mum position (must be within 80%

to 100% of range). Ad just the Span con trol for

max i mum out put cur rent of 20 mA. Re check the

zero set ting and adjust if nec es sary. Re check the

Span setting and readjust if nec es sary.

NOTE

Mount with Ø.50 or M12 Socket Head Cap Screws.

Alternate Wire Rope Exit

[email protected] www.dspmindustria.it