Casio 2590 Kullanıcı Kılavuzu - Sayfa 2
İzle Casio 2590 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Casio 2590 3 sayfaları. 2590; 2591
Sayfayı Yazdır
USER'S GUIDE 2590/2591
4. While a setting is flashing, press D to increase it.
• To set an alarm that does not include a month (Daily alarm, Monthly alarm),
x
for the month. Press D until the
set
month setting is flashing.
• To set an alarm that does not include a day (Daily alarm, 1-Month alarm),
for the day. Press D until the
set
xx
xx
month and 1) while the day setting is flashing.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. or p.m. (PM/P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off or change it to a one-
time alarm.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the alarm
1
setting screen
To test the alarm
• In the Alarm Mode, hold down D to sound the alarm.
2
5
To turn Alarms
through
and the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select a one-time alarm
(alarm number
(
:00
).
2. Press A to toggle it on and off.
• The on/off status of Alarms
Time Signal is shown by indicators along the bottom of
the displays.
• The alarm on indicators and Hourly time Signal on
indicator are displayed in all modes.
• While an alarm is sounding, the applicable alarm on
Hourly time signal
indicator flashes on the display.
on indicator
Alarm on indicator
To select the operation of Alarm
1
1. In the Alarm Mode, use D to select Alarm
2. Press A to cycle through the available settings in the sequence shown below.
Snooze on indicator and Alarm
Press
.
One-time
Snooze
alarm on
alarm on
1
• The snooze on indicator and Alarm
on indicator are displayed in all modes.
• The snooze on indicator flashes during the 5-minute intervals between alarms.
1
• The alarm indicator (Alarm
on and/or snooze on) flashes while the alarm is
sounding.
Countdown Timer
The countdown timer can be set within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• Countdown timer functions are available in the
Countdown Timer Mode, which you enter by pressing
C.
Hour : Minutes Seconds
To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
To set the countdown start time
1. In the Countdown Timer Mode, hold down A until the
hours setting of the countdown start time starts to flash,
which indicates the setting screen.
2. Press C to move the flashing between the hours and
minutes settings.
3. While a setting is flashing, use D to change it.
• To set the starting value of the countdown time to
24 hours, set
4. Press A to exit the setting screen.
To turn auto-repeat on and off
1. In the Countdown Timer Mode, hold down A until the
hours setting of the countdown start time starts to flash,
which indicates the setting screen.
2. Press B to toggle auto-repeat on (
off (
not displayed).
• Note that pressing B in the above operation also turns
on the backlight.
• When the end of the countdown is reached while
auto-repeat is on, the alarm sounds, but the countdown
Auto-repeat indicator
restarts from the beginning without stopping. You can
stop the countdown by pressing D and manually reset
to the start time by pressing A.
• The auto-repeat indicator appears in the Countdown
Timer Mode only.
x
mark appears (between 12 and 1) while
mark appears (between the end of the
2
5
through
) or the Hourly Time Signal
2
through
5
and the Hourly
1
.
1
on indicator
0:00
.
displayed) and
Stopwatch
The stopwatch lets you measure elapsed time, split times,
1/100 second
and two finishes.
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
Hours
Minutes
elapsed time measurement.
• All of the operations in this section are performed in the
Seconds
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
Elapsed time
Start
Stop
Re-start
Split time
Start
Split
Split release
(SPL displayed)
Two Finishes
Split
Stop
Start
First runner
Second runner
finishes.
finishes.
Display time of
first runner.
Dual Time
The Dual Time Mode lets you keep track of time in a different time zone.
• In the Dual Time Mode, the seconds count is synchronized with the seconds count
of the Timekeeping Mode.
To set the Dual Time
1. Press C to enter the Dual Time Mode.
2. In the Dual Time Mode, hold down A until the hour
Hour : Minutes Seconds
setting starts to flash, which indicates the setting
screen.
3. Press C to change the selection in the following
sequence.
Hour
4. Press D to increase the setting.
5. Press A to exit the setting screen.
Backlight
The backlight uses an LED (light-emitting diode) and a
light guide panel that cause the entire display to glow for
easy reading in the dark. The watch's auto light switch
automatically turns on the backlight when you angle the
watch towards your face in the dark.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See "Backlight Precautions" for other important
information about using the backlight.
Auto light switch indicator
To turn on the backlight manually
In any mode, press B to illuminate the display for about
one second.
• The above operation turns on the backlight regardless
of the current auto light switch setting.
About the Auto Light Switch
Turning on the auto light switch causes the backlight to turn on for about one second,
whenever you position your wrist as described below in any mode. Note that this
watch features a "Full Auto LED Light," so the auto light switch operates only when
available light is below a certain level. It does not turn on the backlight under bright
light.
• Be sure to wear the watch on the outside of your left wrist while using the auto light
switch.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you more than 40 degrees causes the backlight to turn on.
Parallel to ground
Warning!
• Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
surprise or distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create
a distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In any mode, hold down B for about two seconds to toggle the auto light switch on
(Auto light switch indicator displayed) or off (Auto light switch indicator not displayed).
• The auto light switch indicator is on the display in all modes while the auto light
switch is turned on.
Stop
Clear
Stop
Clear
Split release
Clear
Display time of
second runner.
Minutes
More than 40 °
2