freecam C310 Kullanıcı Kılavuzu - Sayfa 2

Güvenlik Kamerası freecam C310 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. freecam C310 2 sayfaları. Solar powered wifi camera
Ayrıca freecam C310 için: Kullanıcı Kılavuzu (2 sayfalar)

Sayfayı Yazdır

2 Device Installation Instructions

This equipment usually can be installed on the wall or pole (ensure there is

sunlight as much as possible). The mounting wall should have certain

thickness and can afford at least three times of the weight of the equipment.

Please select the mounting position as required.

2.1 Prior to installation of the product, first confirm steady WiFi signals (at

least two grids of signals) in installation position with mobile phone. When

the installation place cannot be covered by WiFi signals, it's allowed to add

WiFi repeater to realize extension. Please install the repeater in the place

between route and camera where there are at least two grids of signals

(Please refer to router and repeater installation and instructions).

2.2 Method of installation on the wall (see Fig. 2.2): tear down the

installation sticker, paste it in the selected position, dig a hole, knock the

expansion bolt into the blank space (please select a sunny place for

installation) .

Router

Repeater

Camera

Fig. 2.1

Fig. 2.2

PIR shield sheet Installation:

2.8.1 Paste the PIR shield sheet in the position of camera PIR device

according to Fig. 2.8.1.

2.8.2 Bend the shield sheet of five areas according to Fig. 2.8.2 so as to

shield the areas.

2.8.3 After an area is shielded, the moving objects in such area cannot

trigger and wake up the camera.

Camera

Detection range

Detection

Camera

range

Horizontal angle

Vertical angle

Note: The shaded area can change with an

appropriate amount according to the bending

angle of the shield sheet.

Fig. 2.8.1

Fig. 2.8.2

2.3 Align the mounting bracket with the installation sticker, and fix the

installation bracket in the position of hole with screw. If you install the

equipment into the wooden wall, the equipment can be fixed by directly

pushing in the screw. Then install the equipment on the bracket, and fix it

with screw (see Fig. 2.3).

2.4 Ribbon type installation method: Such method applies to installation of

the equipment on the pole. First bind the installation bracket onto the pole

with ribbon, and tighten the ribbon as much as possible. Then install the

equipment onto the bracket, and fix it with screw (see Fig. 2.4).

2.5 In selecting installation place, please note:

2.5.1 Please try to select a place with plentiful sunshine for installation.

2.5.2 Avoid installing the equipment in the place where the equipment is

disturbed by the object which moves frequently as much as possible.

180°Adjust

Adjust 90° up and down

90°Adjust

Tighten the screw

Fig. 2.3

Fig. 2.4

Product Dimension

155

161

100

29.5

(Dimension:mm)

Accessories

①

②

③

④

Operation instruction of

Quality certificate

C310 product

⑤

⑥

⑦

⑧

Installation sticker × 1

② Mounting base bracket × 1

①

③ Screw set × 1

④ PIR shield sheet × 1

⑤ Charging cable × 1

⑥ Quality certificate×1

⑦ Operation instruction of C310 product× 1

⑧ Ribbon×2

2.6 Sunlight distribution of the world (see Fig. 2.6). Please confirm whether

the installation is appropriate according to the sunlight distribution of the

country or region where you are located (you might need to charge the

camera with charger regularly for the country or region where the average

peak sunshine duration is within 1.0-2.9).

Note: Peak sunshine means the maximum solar irradiance which can be

obtained in most places of the earth surface on sunny days – 1000 w/m2.

2.7 The operating time of this camera is related to charging time of

sunlight and the number of times of triggering and waking up. Fig. 2.7

describes and expresses the relation among these three factors. Please

refer to it when using this product.

Fig. 2.6

Technical Parameters

Item

Specification

Product model

C310 Solar Intelligent WiFi camera

Lens

3.6mm / M12/90 degrees

Video

H.264 encoding

Audio

Support

WiFi

Support IEE802.11b / g / n protocols(4GHz)

Infrared fill light

Support

PIR body induction

Induction distance ≈ 5 meters

If there is no operation within 30 seconds after trigger is

Cycle time

started, enter the sleep state

Network P2P traversal

Support

Battery power indicator

APP support

Maximum output current is [email protected], which will

Standard solar panel

change according to solar intensity and incident angle

Extensible storage space

Extensible storage space: Built-in 16GB Micro SD card

6800mAh, charged with solar energy 20 hours per

Battery and standby

month. Wake up or trigger startup for 10 to 20 times per

day, and can be used for a long time

Dimension

161 × 155 × 108 mm

Net weight

800 g

Waterproof level

IP55

The number of wake-up times

Average sunshine time (hour)

Black 0

Red

Blue

Green 3

Note: The shaded area means

charging the equipment

artificially according to

practical situation.

Continuuous working time

of camera (day)

120

Fig. 2.7

2.8 Notes:

PIR detection is a high-sensitivity detector which is used for infrared

detection of object motion. Therefore, motion detection can be triggered

by the change of sunshine when cloud layer moves fast outdoors, the

movement of automobile, and the floating of leaves caused by wind.

If user discovers false alarm frequently , please find

reasons and use "PIR shield sheet" to cover this

interference area. If the shield sheet still not work, you

can select "security" option in APP and turn off the

"motion detection" function in "Protection" option

Notice

until environment return to normal, you can open and

use this function again.

FreeCam's common problems and solutions

1 Equipment adding failure.

Several causes leading to equipment adding failure:

① Pending time-out error at App equipment adding

Solution: If the WiFi status indicator blinks red over one minute, please

press the reset button for 3-5 seconds till the WiFi status indicator blinks

blue, then confirm if the router signal is favorable and input correct router

password to re-add the equipment.

② A prompt message "Please input the default password, 11111111" on

some Android mobile phone;

Solution: The failure is caused by connection abnormity between mobile

phone and camera hot point; first of all, please access to WiFi setup

interface of mobile phone to connect to the camera (hot point name is

DOG-***) manually, and then return to app; if the failure still exists, please

turn off the mobile phone WiFi and turn it on again. Repeat the

above-mentioned connection method manually to add the equipment

smoothly.

2 Whether C310 solar intelligent WiFi camera can work all the time?

How to deal with power outage while using the equipment?

The equipment can be used for long-term in case of 4-5 days of sun

irradiation charging every month and 10-20 times of triggering actions. If it

displays as low battery:

① Reduce awakening arising from false alarm as far as possible; use PIR

shilding case or turn off motion detecting function to save electric quantity.

② Charge for the camera with a common USB charger indoor or with a

charger.

3 Whether the contents stored at the TF card of the camera can be

reviewed on a PC?

The videos stored in the camera can be reviewed with a mobile phone

with WiFi available or remove TF card to insert to a PC card reader. Use

FreeCam PC client-side to review the record.