Consort BHM2SL Kurulum ve Kontrol Kılavuzu - Sayfa 2
Isıtıcı Consort BHM2SL için çevrimiçi göz atın veya pdf Kurulum ve Kontrol Kılavuzu indirin. Consort BHM2SL 4 sayfaları.
Sayfayı Yazdır
2
Overview
Please read this guide carefully and retain for future
use and maintenance.
This appliance has been designed and manufactured
to the highest international standards, however, care
must be taken for optimal results and safety. This
appliance also meets the requirements of EU Directive
2004/106/EC for EMC and 2009/125/EC Directive.
Safety & Care
The appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities or lack of experience and
knowledge unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should be
supervised to ensure that they do not play with the
appliance.
Warning
Do NOT site the appliance into a corner.
Do NOT handle the appliance with wet hands.
Do NOT use the appliance in workshops or rooms
where excessive dust is generated or present.
Ensure that nothing is pushed into any aperture of
this appliance.
Do NOT touch outlet grille when the appliance is in
use.
Do NOT cover or restrict any aperture of the
appliance when in use.
Do NOT use the appliance if damaged.
Do NOT leave the appliance unattended where
young children are present.
Thermally Operated Cut-Out
The appliance is fitted with a thermally operated cut-
out (TOC). This is a safety device, which switches the
heater off if, for any reason, the appliance overheats.
The TOC can only be re-set after the appliance has
cooled down. In order to re-set the TOC, proceed as
follows:
Switch off appliance and leave for
approximately 5 minutes. This can be done
by using the controller.
Switch appliance back on and TOC will re-
set.
Ensure that the appliance is functioning
correctly. If the TOC control operates again,
the appliance should be checked by a
competent electrician.
The heater carries a 'Do Not Cover' label to warn the
user that if the appliance is covered, there is a risk of
overheating.
64000284 Iss 01
Cleaning
Always disconnect the heater from the mains before
cleaning. The heater should not require any
maintenance, but it is strongly advised that it is kept
clean. An occasional wipe over with a soft cloth is all
that should be necessary.
Do NOT use metal or furniture polish on any part of
the heater.
Do NOT touch the heater with wet hands or in any
way bring water into contact with it.
If the supply cord is damaged, it must be replaced by
the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
If Your Heater Does Not Work
Check that power is available to the heater.
Check that the thermal cut-out has not operated.
Follow the reset instructions given under the section
headed 'Thermal Operated Cut-out'.
Check that the fuse in the spur unit has not blown.
This can be done by replacing the fuse with
another suitable fuse.
Should neither of the above remedies work, then
telephone the helpline number shown in these
instructions (UK ONLY). Do not attempt to repair the
heater.
Connection to the Main Supply
Electrical installation should be carried out by a
competent installer, preferably registered with NICEIC
(National Inspection Council for Electrical Installation
Contracting) in accordance with the 17 edition of the
IEE Wiring Regulations, (BS.7671), and any relevant
Local Authority Bye-Laws. This heater is fitted with a 3-
core mains supply cable and should be permanently
connected to the electricity supply via a double pole
switch having 3mm gap on each pole. A switched
Fused Connection unit to BS.1363. Part 4 is a
recommended mains supply connection accessory to
ensure compliance with safety requirements
applicable to fixed-wiring installation.
Note: When switched on for the first time the
appliance may emit a slight smell. This is purely the
evaporation of a fluid used in the manufacturing
process.
WARNING: This appliance must be earthed.