Dyna-Form Mercury Advance Kullanıcı Kılavuzu - Sayfa 9

Tıbbi Ekipman Dyna-Form Mercury Advance için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Dyna-Form Mercury Advance 12 sayfaları. Pressure relieving mattress suitable for use with patients at very high risk of pressure ulcer damage

Sayfayı Yazdır

7.4 Alternating Mode Failure (no alternation)

This will be indicated by a warning LED on A and B and an Audible Warning.

1. Reset the warning – turn off Power and press the Audible Warning mute button.

2. Disconnect the air hoses to reduce pressure – reconnect when pressure has decreased.

7.5 Initialising Failure

This will be indicated by a warning LED on A, B and C and an Audible Warning.

1. Press the Audible Warning mute button to silence the Audible Warning.

2. Check the power cable is firmly plugged into the mains outlet and the Control Unit;

and check the mains power is switched on.

3. Check the Control Unit fuse (1 AMP) – fuses can be released using a screwdriver

to push and turn.

8. Maintenance Procedures

8.1 Safety Warning

Only qualified technicians trained or formally approved by Direct

Healthcare Services Ltd. in the operation and maintenance of

Direct Healthcare Services products may carry out maintenance,

modification or repair work on the equipment. Unqualified

personnel attempting to work on Direct Healthcare Services

Control Units risk serious injury to themselves and others and

possibly death by electrocution. Inlet fuse NOT to be replaced by

operator or patient, to be replaced by service personnel only.

Warning – Do not modify this equipment without

authorisation of Direct Healthcare Services.

8.1.1 Servicing

A service light will illuminate when a service is due.

Direct Healthcare Services (DHS) recommend that the Control

Unit should be serviced every 8760 hours of operation (one

continuous year running). The unit contains no user serviceable

parts and should only be carried out by persons as described

in section 8. 1 . DHS will make available on request all manuals,

component parts lists and other information necessary for any

suitably qualified person (As in 8. 1 ) to carry out repair or service the

system. For Service, maintenance and any questions regarding this

please contact DHS.

8.2 Cleaning Procedures

Warning: Before cleaning the System make sure that the Control

Unit is disconnected from the mains electricity supply.

Do not immerse the Control Unit in water or other fluids.

Do not autoclave, nor use phenol for cleaning.

Do wash hands before commencing the cleaning process.

Wear appropriate protective clothing such as gloves, apron

and a mask.

Ensure all work surfaces are cleaned before and after contact

with the Mattress.

U S E R M A N U A L

8.3 Warning – Cleaning the Mattress

1. Cleaning should take place after use or between patients.

2. With cover left on the Mattress disconnect the Mattress from

3. Clean the surface of the wash down table with Hypochlorite

4. Wash Mattress top using hot water (60 degrees C) containing

5. Use a Hypochlorite solution 1,000 parts per million available

6. Using suitable brush, hot water, detergent or Hypochlorite

7. If required, the Mattress Cover may be removed and

8. To avoid shrinkage of the coverline dry in an indoor clean

8.4 Warning – Cleaning the Control Unit

The Control Unit can be cleaned by wiping with a cloth

dampened with a detergent solution or Hypochlorite solution.

Also, refer to symbol chart.

8.4.1 Warning

Ensure the Mercury Advance System is not exposed to:

1. Excessive heat sources e.g. fires, radiators etc.

2. Water, particularly immersion of the Control Unit.

D I R E C T H E A L T H C A R E S E R V I C E S . C O . U K

the Control Unit.

solution or equivalent disinfectant.

detergent – dry with a paper towel.

chlorine. For heavy contamination use a Hypochlorite solution

10,000 parts per million available chlorine. Please ensure

thorough rinsing after cleaning.

solution, clean Umbilical Hose and CPR Valve. Dry with

paper towel.

machine-washed at a temperature of 80 degrees C, for not

less than 10 minutes. The individual Air Cells can be wiped

down with established disinfectants.

environment or tumble dry on a low heat setting not

exceeding 40 degrees C and not for longer than 10 minutes.

Covers must be thoroughly dried before re-fitting to the

mattress.