Emeril Lagasse PPC772P Kullanıcı El Kitabı - Sayfa 8
Elektrikli Düdüklü Tencere Emeril Lagasse PPC772P için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Emeril Lagasse PPC772P 17 sayfaları.
Sayfayı Yazdır
Instructions for Pressure Lid Assembly
INNER LID ASSEMBLY
REMOVING LID
1. Hold the Knob on the underside of the Inner Lid and pull
to remove the Inner Lid (see Fig. i).
INSERTING INNER LID
1. Ensure that the Knob on the underside of the Inner Lid is facing
outward, away from the Lid.
2. Ensure that the Inner Lid Rubber Gaskets are properly attached
to the Inner Lid (see Fig. ii-a & ii-b).
3. Press the Inner Lid onto the Lid and press the hole on the Inner
Lid onto the Center Knob on the underside of the Lid (see Fig. iii).
4. Ensure that Knob is visible when the Inner Lid is in place and that
the Inner Lid Rubber Gaskets are positioned evenly and onto the
rim of the Inner Lid (see Fig. ii-a).
CHANGING OR CLEANING THE INNER LID
1. Hold the Knob on the underside of the Inner Lid and pull
to remove the Inner Lid (see Fig. i).
2. Pull off the Inner Lid Center Gasket (see Fig. iv) and the Inner Lid
Outer Gasket (see Fig. ii-b).
3. Clean the Inner Lid Rubber Gaskets after each use. Inspect the
Inner Lid Rubber Gaskets to ensure that they are clear of debris.
4. Place the new or clean Inner Lid Center Gasket in the hole
in the Inner Lid (see Fig. v). Attach the new or clean Inner Lid
Outer Gasket to the outside of the Inner Lid. When properly
attached, the Inner Lid Rubber Gaskets should sit evenly.
5. Ensure that the Knob on the Inner Lid is facing outward, away
from the Lid. You should be able to see the Knob (see Fig. ii-a).
6. Press the Inner Lid onto the Lid and press the hole on the Inner
Lid onto the Center Knob on the underside of the Lid (see Fig. iii).
7. Ensure that Knob is visible when the Inner Lid is in place and that
the Inner Lid Rubber Gaskets are positioned evenly and onto the
rim of the Inner Lid (see Fig. ii-a).
14
Emeril Lagasse Pressure Cooker Plus™ | Models: PPC771, PPC772 & PP772P
FIG. i
FIG. ii-a
FIG. ii-b
FIG. iii
FIG. iv
FIG. v
Instructions for Pressure Lid Assembly
FLOAT VALVE AND RED PRESSURE
INDICATOR ASSEMBLY
1. Remove the Lid from the Unit and remove the Inner Lid
(see INNER LID ASSEMBLY, p. 14).
2. Pull off the Rubber Gaskets at the bottom of the Float Valve and
Red Pressure Indicator (see Fig. vi). Remove the Red Pressure
Indicator through the top of the lid. The Float Valve will be loose in
its chamber.
3. Inspect that no food is stuck in the chambers and run water
through them to clean them. Be cautious not to submerge the
whole Pressure Lid.
4. When the chamber is clear of debris, turn the Pressure Lid right
side up to allow the Float Valve to drop into the Float Valve
Chamber on the underside of the Lid. Turn the lid to the side so
you can view the Float Valve
5. Stick a pin or paperclip into the hole on the side of the Float Valve
(see Fig. vii; the pictured pin is not included).
6. With the pin or paperclip inserted into the side hole, slide the
Rubber Gasket onto the Float Valve, ensuring that the wider side
of the Rubber Gasket is against the Pressure Lid (see Fig. viii). The
Rubber Gasket should be snug on the Float Valve.
7. Remove the pin or paperclip (see Fig. vii).
8. Insert the Red Pressure Indicator into the lid. Use your finger to
hold the Red Pressure Indicator in place. While holding the Red
Pressure Indicator in place, slide the Rubber Gasket onto the Red
Pressure Indicator, ensuring that the wider side of the Rubber
Gasket is against the Pressure Lid. The Rubber Gasket should be
snug on the Red Pressure Indicator.
PRESSURE RELEASE VALVE ASSEMBLY
NOTE: DO NOT ATTEMPT TO ASSEMBLE OR DISASSEMBLE
THE PRESSURE RELEASE VALVE WHEN THE EMERIL
LAGASSE PRESSURE COOKER PLUS IS IN USE.
1. Pull to remove the Pressure Release Valve (see Fig. ix).
2. Ensure that the Pressure Release Valve and holes are not blocked
by food or debris. If blocked, wash out or use a pin to unblock.
3. Look at the clip on the underside of the Pressure Release Valve
(see Fig. x). It should not be damaged or severely bent.
4. Press the Pressure Release Valve back into the hole on the Lid.
If the Valve does not insert correctly, it may have a bent clip.
FIG. vi
FIG. vii
Insert
Remove
FIG. viii
FIG. ix
FIG. x
15
Emeril Lagasse Pressure Cooker Plus™ | Models:PPC771, PPC772 & PP772P