Hifonics ZeusZxi 8008 Kullanıcı Kılavuzu - Sayfa 10
Amplifikatör Hifonics ZeusZxi 8008 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Hifonics ZeusZxi 8008 15 sayfaları. Zeus 25th anniversary edition high performance amplifier
Sayfayı Yazdır
- 1. Table of Contents
- 2. General Installation Procedure
- 3. Amplifier Feature Descriptions
- 4. Zxi6008 / Zxi1008 / Zxi1308 2 CHANNEL AMPLIFIER APPLICATIONS
- 5. Zxi4408 / Zxi6408 / Zxi8808 4 CHANNEL AMPLIFIER APPLICATIONS
- 6. Zxi8408 5 CHANNEL AMPLIFIER APPLICATIONS
- 6. Channel Discrete, One Being Mono Low Pass / 3 or 4 Channel Discrete, One Being Mono Low Pass / 3 Way Active
- 6. Front/Rear High Pass, with Constant Sub Bass
- 7. Setting up Systems after Installation for Best Performance
- 8. Troubleshooting and Diagnostics
- 9. Features and Specifications
- 10. Product Warranty
ZXi8008 5 CHANNEL AMPLIFIER APPLICATIONS
3 way active, with mono bass
The ZXi8008 5 channel amplifier contains all the functions necessary to set up a
completely self contained 3 way active crossover system.
Interconnect cable checklist:
Use good quality RCA cables to connect the inputs of channels 1&2 to the full
range outputs of the source.
Switch setting checklist:
- INPUT MODE: CH2
- CH 1 / 2 X-OVER: HP
- CH 3 / 4 X-OVER: BP
Crossover frequency control checklist:
- CH 1 / 2 HIGH PASS: 1KHz to 4KHz
- CH 3 / 4 HIGH PASS: 100 Hz
- CH 3 / 4 LOW PASS: 1KHz to 4KHz
- CH 5 LOW PASS: 100 Hz
CH 1&2
FULL RANGE
INPUTS
Front/rear high pass, with constant sub bass
Another obvious application for the ZXi8008 is to use 4 channels for front/rear
satellites, and the mono channel for constant non faded sub bass.
Interconnect cable checklist:
Use good quality RCA cables to connect channels 1,2,3&4 inputs to the front
and rear outputs of the source as shown.
Switch setting checklist:
INPUT MODE: 4CH
- CH 1 / 2 X-OVER: HP
- CH 3 / 4 X-OVER: HP
Crossover frequency control checklist:
- CH 1 / 2 HIGH PASS: 100 Hz
- CH 3 / 4 HIGH PASS: 100 Hz
- CH 3 / 4 LOW PASS: N/A
- CH 5 LOW PASS: 100 Hz
CH 1&2
FRONT
INPUTS
CH 3&4
REAR
INPUTS
8
Note that the HIGH and LOW PASS controls of channels 3&4 act as the
bandpass controls.
Please note that these frequency points are suggestions only. Refer to the
loudspeaker manufacturer specifications and the section "Setting up systems
after installation for best performance"
Level control checklist:
- Refer to the section "Setting up systems after installation for best performance"
Minimum final loudspeaker impedances:
- 2 ohm per channel
Please note that these frequency points are suggestions only. Refer to the
loudspeaker manufacturer specifications and the section "Setting up systems
after installation for best performance"
Level control checklist:
- Refer to the section "Setting up systems after installation for best performance"
Minimum final loudspeaker impedances:
- 2 ohm per channel
CH 5 MONO
SUBWOOFER
CH 3&4
REAR HIGHS
SPEAKERS
CH 1&2
TWEETERS
TO BATTERY +12v
VIA FUSE
REMOTE TURN-ON
CHASSIS GROUND
CH 5 MONO
SUBWOOFER
CH 3&4
REAR HIGHS
SPEAKERS
CH 1&2
FRONT HIGHS
SPEAKERS
TO BATTERY +12v
VIA FUSE
REMOTE TURN-ON
CHASSIS GROUND