Hifonics ZeusZxi 8008 Kullanıcı Kılavuzu - Sayfa 4

Amplifikatör Hifonics ZeusZxi 8008 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Hifonics ZeusZxi 8008 15 sayfaları. Zeus 25th anniversary edition high performance amplifier

Hifonics ZeusZxi 8008 Kullanıcı Kılavuzu

AMPLIFIER FEATURE DESCRIPTIONS

ZEUS ZXi SERIES AMPLIFIERS
Each model is capable of 4 & 2 ohms stereo per channel, or 4 ohms mono bridged
operation.
Tri-Mode operation with any stereo pair of amplifier channels is possible, as with all
bridgeable amplifiers.
The input sensitivities for rated output powers are variable from 0.2 volt to 6 volt.
All crossovers are fully variable in their respective ranges.
B O O S T
H F R - 3
MI N MA X X
The X-OVER slide switch selects the internal crossover functions:
- The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER
setting simplifying daisy chaining of amplifiers.
- HI: Selects the built in HIGH PASS filter, variable from 10 Hz to 150Hz.
- FLAT: Bypasses all crossovers for full frequency range operation.
LP/BP: Selects the built in LOW PASS filter, variable from 30 Hz to 150 Hz.
The AMPLIFIER CH 1/2CH X-OVER slide switch selects the input signal for channel
pair 1 & 2:
- HI: Selects the built in HIGH PASS filter, variable from 10 Hz to 150Hz.
- FULL: Bypasses all crossovers for full frequency range operation.
- LP/BP: Selects the built in LOW PASS filter, variable from 30 Hz to 150Hz.
Note that the LOW PASS signal is MONO:
- In the LP/BP position, the HIGH PASS filter acts as a subsonic filter.
- When the LP/BP mode is selected, a 0 to +10 dB, at 45 Hz, BASS EQ is also switched
in.
The ZXi8006 has three sets of inputs:
Line inputs on RCA jacks for channel pairs 1&2, 3&4, and MONO channel 5. These inputs
can be used in various combinations, to suit the application, depending on the settings of
the INPUT MODE switch, and the X-OVER switches for channels 1&2, and channels 3&4,
respectively.
INPUT MODE slide switch:
- In the CH2 position, ALL five amplifier inputs are selected from the CH1/CH2 RCA jacks.
Channel 5 receives a mono mixed signal.
- In the 4CH position, channel pair 1&2 receive input signal from RCA jacks CH1 and CH2,
and channel pair 3&4 receive input signal from RCA jacks CH3 and CH4. A mono mixed
signal from these four RCA jacks are also fed to channel 5.
- When 5CH DISCRETE is selected, each channel receives an input signal from its
respective input RCA jack. Channel 5 has two jacks on its LINE INPUT, which are summed
together.
2
ZXi6008 / ZXi1008 / ZXi1308 2 CHANNEL AMPLIFIERS
LINE INPUT
ZXi4408 / ZXi6408 / ZXi8408 4 CHANNEL AMPLIFIERS
LINE INPUT
MODE
CH1
CH3
CH2-CH4
10Hz-150Hz
CH2
CH4
REMOTE
10Hz-150Hz
ZXi8008 5 CHANNEL AMPLIFIERS
LINE INPUT
HI PASS
MODE
CH1
CH3
Ch2 Ch5
Ch4
50Hz- 4Khz
5CH
LOW PASS
REMOTE
CH2
CH4
30Hz-150Hz
Crossover filter slopes are 12 dB/octave for stereo filters, and 24 dB/octave for mono
filters.
A POWER LED indicates the powered "up" and turned "on" condition.
All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short
circuit, and amplifier DC faults indicated by the DIAGNOSTIC, or PROTECT LED.
CH1
HI PASS
X-OVER
10Hz 150Hz
REMOTE
HP FULL LP/BP
CH2
Note that the LOW PASS signal is MONO.
- In the LP/BP position, the HIGH PASS filter acts as a subsonic filter.
When the LP/BP mode is selected, a 0 to +10 dB, at 45 Hz, BASS EQ is also switched
in.
The REMOTE jack enables dash mount level control of the LOW PASS signal.
1/2 CH
HI PASS
LOW PASS
BASS EQ
X-OVER
30Hz-150Hz 0dB-10dB
HI FULL LP/BP
3/4 CH
HI PASS
LOW PASS
BASS EQ
X-OVER
HI FULL LP/BP
30Hz-150Hz 0dB-10dB
The AMPLIFIER CH 3/CH 4 X-OVER slide switch selects the input signal for channel
pair 3&4
- Hi: Selects the built in HIGH PASS filter, variable from 10 Hz to 150Hz.
- FULL: Bypasses all crossovers for full frequency range operation.
- LP/BP: Selects the built in LOW PASS filter, variable from 30 Hz to 150 Hz.
Note that the LOW PASS signal is MONO.
- In the LP/BP position, the HIGH PASS filter acts as a subsonic filter.
- When the LP/BP mode is selected, a 0 to +10 dB, at 45 Hz, BASS EQ is also switched in.
- Full range signal from channels 1 / 2 inputs are routed to the Line OUT RCA jacks,
regardless of the setting of the X-OVER switches.
- The REMOTE jack enables dash mount level control of the LOW PASS signal, CH3/4 only.
1/2 CH
3/4 CH
LEVEL
HI PASS
X-OVER
X-OVER
6V 0.2V
50Hz- 150hz
HI
FULL
HI-FULL BP
LEVEL
5CH
BASS EQ
0dB-10dB
6V 0.2V
CH1/2 X-OVER slide switch:
FULL: Sets this pair to full range operation.
HP: Selects the built in HIGH PASS filter, variable from 50 Hz to 4 KHz.
CH3/4 X-OVER slide switch:
- FULL: Sets this pair to full range operation.
- B.P. : In this mode, the HIGH PASS ranges from 50Hz to 150Hz and the LOW
PASS filter ranges from 250Hz to 4KHz, are selected to form a BANDPASS
c r o s s o v e r f i l t e r.
- HP: Selects the HIGH PASS filter, variable from 50Hz to 4KHz.
CH 5:
- The channel 5 functions were chosen to be very specific to mono bass operation, and not
switchable:
- The LOW PASS filter has a variable range from 30 Hz to 150 Hz.
- The BASS EQ gives a bass boost, 0 to +10 dB, at 45 Hz.
LOW PASS
BASS EQ
LEVEL
POWER
30Hz 150Hz 0dB 10dB 6V 0.2V
PROTECT
LEVEL
POWER
LINE OUT
L
6V 0.2V
PROTECT
LEVEL
6V 0.2V
R
LOW PASS
LEVEL
POWER
PROTECT
250Hz-4KHz
6V 0.2V
LINE OUT
L
R