Autonics TK4S Ürün Kılavuzu - Sayfa 2

Sıcaklık Kontrolörü Autonics TK4S için çevrimiçi göz atın veya pdf Ürün Kılavuzu indirin. Autonics TK4S 6 sayfaları. Simultaneous heating&cooling output pid temperature controllers
Ayrıca Autonics TK4S için: Manuel (2 sayfalar), Kullanım Kılavuzu (2 sayfalar)

Sayfayı Yazdır

• Install a power switch or circuit breaker in the easily accessible place for supplying or

disconnecting the power.

• Do not use the unit for other purpose (e.g. voltmeter, ammeter), but temperature

controller.

• When changing the input sensor, turn off the power first before changing. After changing

the input sensor, modify the value of the corresponding parameter.

• 24 VACᜠ, 24-48 VDCᜡ power supply should be insulated and limited voltage/current or

Class 2, SELV power supply device.

• Do not overlapping communication line and power line. Use twisted pair wire for

communication line and connect ferrite bead at each end of line to reduce the effect of

external noise.

• Make a required space around the unit for radiation of heat. For accurate temperature

measurement, warm up the unit over 20 min after turning on the power.

• Make sure that power supply voltage reaches to the rated voltage within 2 sec after

supplying power.

• Do not wire to terminals which are not used.

• This unit may be used in the following environments.

- Indoors (in the environment condition rated in 'Specifications')

- Altitude Max. 2,000 m

- Pollution degree 2

- Installation category II

Ordering Information

This is only for reference, the actual product does not support all combinations.

For selecting the specified model, follow the Autonics website .

❶

❶ Size

N: DIN W 48 × H 24 mm

SP: DIN W 48 × H 48 mm (11 pin plug type)

S: DIN W 48 × H 48 mm

M: DIN W 72 × H 72 mm

W: DIN W 96 × H 48 mm

H: DIN W 48 × H 96 mm

L: DIN W 96 × H 96 mm

❷ Option in/output

Size: N

PN OUT2

Function

Normal type

Alarm 1 + CT input

01)

Heating & Cooling Alarm 2

Normal type

Alarm 1 + Alarm 2

Normal type

Alarm 1 + Digital input 1/2

Heating & Cooling Digital input 1/2

Alarm 1+Transmission

Normal type

output

Heating & Cooling Transmission output

Alarm output 1 + RS485

Normal type

communication

Heating & Cooling RS485 communication

Size: SP

PN Function

Alarm 1

Size: S, M, W, H, L

PN Function

Alarm 1

Alarm 1 + Alarm output 2

Alarm 1 + Transmission output

Alarm 1 + RS485 communication

Alarm 1 + Alarm 2 + Transmission output

Alarm 1 + Alarm 2 + RS485 communication

Alarm 1 + Alarm 2 + Digital input 1/2

01) The CT input model of TK4N can be selected only in the normal type model with alarm output 1. (except

TK4SP)

02) Only for TK4S-D, OUT2 output terminal is used as DI-2 input terminal.

03) When operating mode is heating or cooling control, OUT2 can be used as alarm output 3 (except TK4N).

04) When operating mode is heating or cooling control, OUT2 can be used as transmission output 2.

Manual

For proper use of the product, refer to the manuals and be sure to follow the safety

considerations in the manuals.

Download the manuals from the Autonics website.

Software

Download the installation file and the manuals from the Autonics website.

■ DAQMaster

DAQMaster is comprehensive device management program. It is available for

parameter setting, monitoring.

❷

❸

❹

❺

❸ Power supply

2: 24 VACᜠ 50/60 Hz, 24-48 VDCᜡ

4: 100-240 VACᜠ 50/60 Hz

❹ OUT1 Control output

R: Relay

S: SSR drive

C: Selectable current or SSR drive

output

❺ OUT2 Control output

N: Normal type

[No OUT2 (Heating or Cooling)]

R: Heating & Cooling type

[Relay output]

03)

C: Heating & Cooling type

[Selectable current or SSR drive

output]

04)

02)

Sold Separately

• 11 pin socket: PG-11, PS-11 (N)

• Terminal protection cover: RSA / RMA / RHA / RLA Cover

• Communication converter: SCM Series

Specifications

Series

TK4N

Power

AC type

100 - 240 VACᜠ 50/60 Hz ±10%

supply

AC/DC type -

Power

AC type

≤ 6 VA

consumption

AC/DC type -

≈ 70 g

Unit weight (packaged)

(≈ 140 g)

Series

TK4W

Power

AC type

100 - 240 VACᜠ 50/60 Hz ±10%

supply

AC/DC type 24 VACᜠ 50/60 Hz ±10%, 24-48 VDCᜡ ±10%

AC type

≤ 8 VA

Power

consumption

AC/DC type AC: ≤ 8 VA, DC ≤ 5W

Unit weight (packaged)

≈ 141 g (≈ 211 g)

Sampling period

50 ms

Input specification

Refer to 'Input Type and Using Range'

• 0.0-50.0 A (primary current measurement range)

CT input

• CT ratio: 1/1,000

• Measurement accuracy: ±5% F.S. ±1digit

Option

input

• Contact - ON: ≤ 2 kΩ, OFF: ≥ 90 kΩ

Digital input

• Non contact - residual voltage ≤ 1.0 V, leakage current ≤ 0.1 mA

• Outflow current: ≈ 0.5 mA per input

Relay

250 VACᜠ 3 A, 30 VDCᜡ 3 A 1a

Control

SSR

11 VDCᜡ±2 V, ≤ 20 mA

output

Current

DC 4-20 mA or DC 0-20 mA (parameter), Load resistance: ≤ 500 Ω

Alarm

AL1, AL2: 250 VACᜠ 3 A 1a

Relay

output

• TK4N AL2: 250 VACᜠ 0.5 A 1a (≤ 125 VA)

DC 4 - 20 mA (Load resistance: ≤ 500 Ω, Output accuracy: ±0.3%

Option

Transmission

F.S.)

output

RS485 comm.

Modbus RTU

Display type

7 segment (red, green, yellow), LED type

Heating, Cooling

Control

ON/OFF, P, PI, PD, PID Control

Heating &

type

Cooling

• Thermocouple, RTD: 1 to 100 (0.1 to 100.0) ℃/℉

Hysteresis

• Analog: 1 to 100 digit

Proportional band (P)

0.1 to 999.9 ℃/℉ (0.1 to 999.9%)

Integral time (I)

0 to 9,999 sec

Derivative time (D)

0 to 9,999 sec

• Relay output, SSR drive output: 0.1 to 120.0 sec

Control cycle (T)

• Selectable current or SSR drive output: 1.0 to 120.0 sec

Manual reset

0.0 to 100.0%

OUT1/2: ≥ 5,000,000 operations

Relay

Mechanical

AL1/2: ≥ 20,000,000 operations (TK4H/W/L: ≥ 5,000,000

life

operations)

cycle

Electrical

≥ 100,000 operations

Between power source terminal and input terminal: 2,000 VACᜠ

Dielectric strength

50/60 Hz for 1 min

0.75 mm amplitude at frequency of 5 to 55 Hz (for 1 min) in each X,

Vibration

Y, Z direction for 2 hours

Insulation resistance

≥ 100 MΩ (500 VDCᜡ megger)

±2 kV square shaped noise by noise simulator (pulse width: 1 ㎲)

Noise immunity

R-phase, S-phase

Memory retention

≈ 10 years (non-volatile semiconductor memory type)

Ambient temperature

-10 to 50 ℃, storage: -20 to 60 ℃ (no freezing or condensation)

Ambient humidity

35 to 85%RH, storage: 35 to 85%RH (no freezing or condensation)

IP65 (Front panel, IEC standards)

Protection structure

• TK4SP: IP50 (Front panel, IEC standards)

Double insulation or reinforced insulation (mark: ▱, dielectric

Insulation type

strength between the measuring input part and the power part: 2

kV)

Accessory

Bracket, Terminal protection cover (TK4N)

Approval

ᜢ ᜧ ᜫ

Communication Interface

■ RS485

Comm. protocol

Modbus RTU

Connection type

RS485

Application standard

EIA RS485 compliance with

Maximum connection

31 units (address: 01 to 99)

Synchronous method

Asynchronous

Comm. Method

Two-wire half duplex

Comm. effective range

≤ 800 m

Comm. speed

2,400 / 4,800 / 9,600 (default) / 19,200 / 38,400 bps (parameter)

Response time

5 to 99 ms (default: 20 ms)

Start bit

1 bit (fixed)

Data bit

8 bit (fixed)

Parity bit

None (default), Odd, Even

Stop bit

1 bit, 2 bit (default)

EEPROM life cycle

≈ 1,000,000 operations (Erase / Write)

• Current transformer (CT)

TK4SP

TK4S

TK4M

24 VACᜠ 50/60 Hz ±10%, 24-48 VDCᜡ ±10%

≤ 8 VA

AC: ≤ 8 VA, DC ≤ 5W

≈ 85 g

≈ 105 g

≈ 140 g

(≈ 130 g)

(≈ 150 g)

(≈ 210 g)

TK4H

TK4L

≈ 141 g (≈ 211 g)

≈ 198 g (≈ 294 g)