AUTOPILOT SYSTEMS Pool Pilot Digital Kullanıcı El Kitabı - Sayfa 8

Aydınlatma Ekipmanları AUTOPILOT SYSTEMS Pool Pilot Digital için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. AUTOPILOT SYSTEMS Pool Pilot Digital 16 sayfaları. Swimming pool and spa purification system

Sayfayı Yazdır

Section 3a – OPERATION

The Pool Pilot™ Digital display will show the PURIFYING OUTPUT LEVEL (in percent %), or whether the system is in

BOOST or SUPER-BOOST Mode on the first line of the two line alphanumeric display. The second line will display the

current TIME in either 12 or 24-hr mode, the TEMPERATURE in either Fahrenheit or Celsius, whether the cell is powered

or not, shown as ON or OFF and Polarity Direction, shown as a "." or blank. Easy touch pads allow for adjusting and

programming the unit. A Check System visual indicator works in conjunction with the display to advise of any problems.

The PURIFYING OUTPUT LEVEL is adjustable from 0% (OFF) to 100 % (MAX) by pressing the Up/Down Arrow to

obtain the desired Purifying Output Level and corresponds to the amount of time the cell is energized during a 15-minute cycle.

The Display will switch between ON and OFF on the lower right corner to indicate if the cell is generating (ON) or in rest

mode (OFF), depending on the Purifier % setting. Little adjustment is needed once the initial setting is established. See page

10 for further details.

Note: The Pool Pilot™ Digital does not test for purifier levels nor automatically adjust to maintain a desired purifier

level. This is done by periodically testing the water and adjusting the output levels up or down, as needed.

The Pool Pilot™ Digital is designed with an AUTOMATIC TEMPERATURE COMPENSATION feature, which

automatically adjusts the output level setting based upon changes in seasonal water temperatures, between 50°F to 90°F (10°C

to 32.2°C) . This unique feature conveniently compensates for warm (more purifier needed) or cold (less purifier needed)

water conditions. The Purifier % display will change automatically when temperature compensated and is considered normal.

The BOOST Button increases the purifier output level from the normal daily setting to 100% for up to 72 hours, and then

returns to the normal setting. The purifying agent is continually produced throughout the normal On/Off cycles of the pump

and throughout all power line disturbances until the end of the boost cycle or is manually deactivated. When Boost is activated

with External Timer setting programmed, the time remaining for the boost cycle is held in memory and will start up in Boost

mode until expired. With One-Speed Pump or Two-Speed Pump setting programmed, the time clock will be over ridden,

producing purifier until the end of the boost cycle. The display will indicate the BOOST Mode on the second line when the

boost Button is pressed once. Once activated, the system will produce the purifying agent for 24 hours. The purifying agent

can be produced for 72 hours by pressing and holding down the Boost Button for 5-seconds from the Boost-Off position. This

is called the SUPERBOOST Mode. The display will indicate that the system has successfully entered the Super Boost mode.

To discontinue operation of Boost mode or Super Boost mode, pressed the Boost Button once more.

The Menu and Select Buttons allows you to view the TEST mode, Program the Functions and Time Clocks. See the

following pages for description of the menu tree.

* The PUMP Button allows you to over ride the pump timer to temporarily turn the pump on or off (depending on its status of

operation), or to manually turn the pump off, indicated by the display "OFF FOR MAINTENANCE". In "OFF FOR

MAINTENANCE" mode, the pump is prevented from restarting by the time clock and is only reactivated only by manually

programming it to turn the pump back on. Not applicable with "EXTERNAL TIMER" selection.

The CHECK SYSTEM light will flash if there is a problem with the system. The nature of the problem will be indicated by

the display through various error messages. See the Troubleshooting section, page 14, for repair solution.

FREEZE PROTECTION

program cycle and run continually (30-minute minimum) when the water temperature falls below 40°F (4.4°C). This prevents

any damage to the PVC due to water expanding as it freezes.

Key Features

Purifier

12:00 P

Boost

this protective feature allows the pump, when programmed for One-Speed Pump, to override the

Digital

100%

80F

Check

System

Select

Pump