Dynatech V-5000 Kullanıcı Talimatları - Sayfa 10

Amplifikatör Dynatech V-5000 için çevrimiçi göz atın veya pdf Kullanıcı Talimatları indirin. Dynatech V-5000 16 sayfaları. Professional

OPERATING MODES:

Always configure your amplifier operating mode before beginning operation. If you want to change it dur-

ing performance. Y ou must decrease the gain controls to their lowest levels to protect the speakers from any popping noise.

Stereo Operation -

Page 14/Diagram 15 details an example of a typical stereo set-up. Connect your inputs into channels one and

two of the amplifier. Connect your speakers to the outputs on the rear of the amplifier. Be sure that your front gain controls are turned

down to their lowest level (full counter-clockwise). Turn your amp on. Turn your input source level up. Use your front gain controls to

regulate the output volume. Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable.

Mono Bridge Operation -

Page 14/Diagram 16 details a mono bridge set-up. Be sure your amplifier and all other audio equip-

ment is powered down. Flip the Stereo/Mono Bridge switch to the Mono Bridge position. Connect an input signal to channel one.

Connect your speaker across the red output binding post on the rear of your amplifier. Turn your equipment on (your amplifier should

always be the last item you turn on). Apply an input source signal to your amplifier. Turn channel two gain up. Use the channel one

gain to regulate your amplifier output.

Bridged-Mono Mode Caution -

The voltage across the output terminals of a bridged V-5000/7000 amplifier may equal or exceed

100 volts RMS and may be as high as 130 volts. Use fully insulated CLASS ONE wiring, and the load must be rated for up to 2500 watts

(@4 ohms)

Parallel Mono -

"Parallel " ties the two channel line inputs together so that they will both be driven by the same signal, without the

need for external jumpers or wiring. Both amplifier channels will operate independently. Though they carry the same signal, their gain

controls affect only their respective channels, and they both must use their respected speaker outputs. Never attempt to parallel the

speaker outputs, this may cause serious damage to your amplifier! This mode is recommended when using the V-5000/7000 to run bass

speakers, to achieve better low end. T o run in parallel mono mode connect your system as you would if you were going to run in stereo

mode. Then flip the mode switch to "MONO." Be sure the amp is off or the power is disconnected before making any changes.

Subwoofer Mode -

This mode sends low frequencies to your speakers without the use of an external cross-over. The subwoofer

operation can be operated in stereo, mono, or bridge mono modes. Change the different operating modes by flipping the mode switch

on the rear of the unit to your desired operating mode. Also, set the subwoofer mode switch to the subwoofer position. Use the frequency

selector to adjust the subwoofer output frequency from 20Hz to 200Hz. The different subwoofer modes are listed as follows;

Bridge Subwoofer - This operation allows you to get the most possible power out of your amplifier for the sole purpose of running a

high powered subwoofer loudspeaker in mono. T o avoid amplifier overheating, never run the amplifier below 4 ohms in this mode. In

this mode you may use the frequency adjustment on the rear of the amp, to control the frequency output level. Frequencies may be

adjusted from 20Hz to 200Hz. Page 13/ Diagram 13 details a typical Bridge Subwoofer set up.

Stereo Subwoofer - This operation is similar to the Bridge Subwoofer operation but in stereo. This operation allows you to run several

subwoofers down to a minimum of 2 ohms. T o avoid amplifier overheating, never run the amplifier below 2 ohms in this mode. Set up

this mode as you would a standard stereo set up. Be sure both channels are set to "SUBWOOF ." In this mode you may use the frequency

adjustment on the rear of the amp, to control the bass frequency output level. Frequencies may be adjusted from 20Hz to 200Hz. Page

13/ Diagram 14 details a typical Stereo Subwoofer set up.

page 10