Decagon Devices EM50G Hızlı Başlangıç Kılavuzu
Veri Kaydediciler Decagon Devices EM50G için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Decagon Devices EM50G 2 sayfaları. Using with a user supplied sim
Ayrıca Decagon Devices EM50G için: Hızlı Başlangıç Kılavuzu (2 sayfalar), Manuel (4 sayfalar), Hızlı Başlangıç (2 sayfalar)
Sayfayı Yazdır
7.
Click the "Download" button on the Em50G toolbar to retrieve
your data from the Decagon Data Service.
8.
After a successful download, the Em50G Downloader will
automatically launch DataTrac. If you do not have DataTrac, a *.dxd
file of your data will be stored in a default location of
"My Documents/ECHO DataTrac/Auto Import".
9.
In DataTrac, the new logger will show up as a new device that
requires configuration. Select the logger and choose "Configure" from
the toolbar. Set the location information if desired, then press "OK".
Downloading Data Subsequent Times
1.
Start "Em50G Downloader". All of the loggers that you have
set up in the previous steps will show up in a list.
2.
The Em50G loggers that you have subscribed to are checked
by default. If you do not want to download data from specific
subscribed Em50G data loggers, uncheck the box beside the loggers
before pressing "download".
3.
Press "Download" to download new data stored in the
Decagon Data Service since the last download. After a successful
download, the Em50G Downloader will launch DataTrac. DataTrac will
automatically process and display the newly downloaded data.
If you have any questions about configuring your Em50G or
downloading data from the Decagon Data Service, please contact
Decagon at: 1-800-755-2751 or [email protected]
13973-01
Introduction
Thank you for purchasing an Em50G data logger. The Em50G is a data
collection device that will allow you to collect and store data from up to five
Decagon sensors. Collected data are uploaded to the Decagon Data Service
using cellular communication technology up to six times a day. You can access
your logger's data from the Decagon Data Service at any time. The Em50G is
configured using ECH2O Utility. Data from the Em50G can be viewed using
DataTrac.
Em50G Logger Configuration
ECH2O Utility is used to configure the Em50G data logger. Please download
the most up to date version of ECH2O Utility from the Decagon website
(www.decagon.com) BEFORE you try to configure your Em50G.
safe place. You will need this number and password to download your data
from the Decagon server.
the included USB cable and initiate ECH2O Utility.
from five minutes to one day.
Communication Configuration
button in the "Communication Option" section. The Em50G uses the cellular
network to transfer measurement data when "Upload data to
ECH2OData.com" box is checked. The Em50G is uploading data to the
Decagon Data Service ("on") by default.
10-11 AM, 1-2 PM, 4-5PM. To conserve battery power, choose fewer
upload times.
2365 NE Hopkins Court
Pullman, Washington 99163
tel: 509-322-2756
Em50G
QuickStart Guide
1.
Take the brightly colored card containing your Device ID and put it in a
2.
To configure the Em50G, directly connect to the Em50G logger using
3.
Choose the sensor plugged into each port.
4.
Pick your measurement interval. Available measurement intervals are
5.
Click "Apply".
6.
To configure the cellular module in the Em50G, click the "Configure"
7.
Choose up to six upload times. Default upload times are: 6-7 AM,