KitchenAid KGCV566RMT01 Kurulum Talimatları Kılavuzu - Sayfa 6
Setüstü Ocak KitchenAid KGCV566RMT01 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. KitchenAid KGCV566RMT01 17 sayfaları. Gas built-in cooktops
Sayfayı Yazdır
If installing
after the cooktop
is phced
into cutout:
Hace the cooktop
upside down on a
protective
surface (bianket,
pad),
burner
box
foam
strip
Giass
cooktops
oniy:
Remove
foam
strip
from
iiterature
package.
Appiy
foam
strip
around
bottom
of cooktop
flush
with
edge.Turn
cooktop
right
side up.
o Carefully
phce
cooktop
into
cutout.
IMPORTANT:
Check that the front
edge
of
the cooktop
is paraHei
to the front
edge
of the countertop.
Lift entire
cooktop
up from
cutout
when
repositioning
cooktop
to prevent
scratching
the countertop.
o Remove
the attachment
screw, s from
seiected
bracket
bcations
on the
bottom
of the burner
box.
Attach
brackets
as shown
so that they
are beyond
edge
of burner
box
and the
champ
screws
(see Step
4) will
contact
the countertop
bottom.Tighten
screws
secureiy.
aoces_
m Instal[
the pressure
regulator
with
the arrow
on the reguiator
pointing
up
toward
unit
and in a position
where
you
can reach
the access
cap.
IMPORTANT:
All connections
must
be
vvrench4ightened.
Do not make
connections
to the gas regulator
too
tight.
Making
the connection
too tight
may
crack the regulator
and cause
a gas
leak. Do not allow
the regulator
to turn
on the pipe
when
tightening
fittings.
adapter
flexible
metal
3/8"
shutoff
valve
"open"
position
to cooktop
\
gas supply
line
m Open
shutoff
valve
in the gas
supply
line, Wait
a few
minutes
for gas to
move
through
the gas line,
9m
Leak testing
of the appliance
shall
be conducted
according
to the following
instructions:
Test ail connections
by brushing
on an
approved
non-corrosive
leak-detection
solution,
Bubbles
wiii
show
a leak,
Correct
any
leak found,
burner
2-1/2"
(6.4 cm)
box
clamping
screw
bracket
attachment
screw
4E
Place the 2q/2"
(6.4 cm) clamping
screws
into
the brackets.
Use
a
screwdriver
to tighten
the screws
against
the countertop.
Do not overtighten.
valve
compound
regulator
All connections
must
be
wrench4ightened.
6m
Assemble
flexible
metal
connector
from
the gas supply
pipe to the pressure
regulator,
You will
need
to determine
the
fittings
required,
depending
on the size
of your
gas supply
line, flexible
metal
connector
and shutoff
valve,
7m
Use pipeojoint
compound
made for
use with NATURAL
and L,R gas, if
flexible
metal connector
is used, be
certain tubing
is not kinked,
E Hug into a grounded
3@rong outlet.
burner
cap
ignitor
__
burner
electrode
"base
m Put burner
caps
on each
burner
base.
Place
burner
grates
over
burner
bases
and caps.