HIKVISION DS-7716NI-I4/16P Hızlı Başlangıç Kılavuzu - Sayfa 2
DVR HIKVISION DS-7716NI-I4/16P için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. HIKVISION DS-7716NI-I4/16P 2 sayfaları.
Ayrıca HIKVISION DS-7716NI-I4/16P için: Hızlı Başlangıç Kılavuzu (17 sayfalar)
Sayfayı Yazdır
1 0
A D D I P C A M E R A S ( c o n t i n u e d )
1) Click an unused camera channel's D
x
checkbox.
2) Click the EDIT (Pencil) button to display the Edit IP Camera window.
3) Use pull-down menu to change Adding Method from "Plug and Play" to "Manual."
4) Enter the camera's IP address and other information as required.
5) Press the OK button to add the camera.
x Hikvision Cameras Not Detected — Must be added manually:
1) Click an unused camera channel's D
x
checkbox.
2) Click the EDIT (Pencil) button to display the Edit IP Camera window.
3) Use pull-down menu to change Adding Method from "Plug and Play" to "Manual."
4) Enter the camera's IP address and other information as required.
5) Press the OK button to add the camera.
NOTE:
If camera does not connect, use SADP program to find and modify camera
settings.
x Third-Party Cameras — Must be added manually:
x
1) Click an unused camera channel's D
checkbox.
2) Click the EDIT (Pencil) button to display the Edit IP Camera window.
3) Use pull-down menu to change Adding Method from "Plug and Play" to "Manual."
4) Enter the camera's IP address and other information as required.
5) Press the OK button to add the camera.
IP Camera Management Icons
Icon
Explanation
Icon
Explanation
Edit basic camera parameters
Upgrade the connected camera
Camera disconnected; click icon
to get camera's exception
Delete the IP camera
information
Play connected camera's live
Camera connected
video
1 2
S E T U P R E C O R D I N G ( c o n t i n u e d )
- Max Bitrate (kbps) is the chosen bitrate for streaming the video. Max Bitrate should be
adjusted to meet or exceed the rate recommended by the system for the chosen
parameters.
- Max Bitrate Recommended is impacted by resolution, quality, and framerate.
- Record Audio turns on audio recording (requires external mic or camera w/built in mic.
- Video Stream determines which stream is recorded. Leave at default (Main Stream).
•
Substream
1.
Go to RECORDING CONFIGURATION > RECORD QUALITY > SUBSTREAM to set up
the Sub Stream to stream to mobile devices and display multiple cameras locally.
NOTE:
If the upload speed is not sufficient, lower the frame rate, bitrate,
and or resolution for more fluent mobile viewing.
. SUBSTREAM TAB
. 3
Select
3 CAMERA
$
Select camera
/
$ STREAM TYPE
Select choice
1
/ RESOLUTION
Can go up only to 4CIF
1 VIDEO QUALITY
Select number of green squares
to set quality (in example,
sensitivity is set to 3)
13
P L A Y B A C K R E C O R D E D V I D E O
1.
Go to MENU > PLAYBACK.
2.
Select the desired camera(s) from the menu on the right of the screen.
3.
Select date (days w/recordings will be blue if continuous only or yellow if all/part of day was event).
4.
Press PLAY.
5.
Click within the timeline to jump to desired time.
3
. PLAYBACK TYPE MENU
Select type of record to play
.
3 FULL SCREEN
Goes to full screen for multiple
channel playback
$ PLAY/STOP
Begin playback (toggles between
Play and Stop)
/
/ CAMERA LIST
Select camera(s) to play back
1 CALENDAR
Select date to play back
1
4 TIMELINE
Click on timeline to jump to
desired playback time
$
1 0
A D D I P C A M E R A S ( c o n t i n u e d )
. NVR CAMERA CHANNELS
Cameras connected to NVR
3 PLAY
Play camera's live video
/
.
$
$ EDIT (Pencil)
Change IP address (in LAN range)
/ CAMERA LIST (White)
1
Added cameras
4
1 LAN CAMERAS LIST (Yellow)
Detected cameras will appear here
2
4 CAMERA CONNECTED
Shows camera is connected
2 CAMERA DISCONNECTED
Shows disconnected camera
( PASSWORD VISIBLE
Show passwords
, ENABLE H.265
Use H.265
11
V I E W L I V E V I D E O
Live View displays real-time video.
Icons in the upper right of screen show
each camera's record and alarm status.
• Alarm (video loss, tampering, motion
detection, sensor alarm, or VCA
alarm)
• Record (manual record, continuous
record, motion detection, alarm, or
VCA triggered record)
• Event/Exception (event and
exception information appears at
lower-left corner of screen)
12
S E T U P R E C O R D I N G
The system defaults to continuously record video at 8 fps, or at 15 fps when motion is detected.
T Recording Schedule
Default is to continuously record everyday. Do the following to change the recording schedule:
1. Go to MENU > RECORDING CONFIGURATION > SCHEDULE.
2. Choose CONTINUOUS or EVENT/(MOTION DETECTION) under the Type pull-down menu.
3. Use cursor to select (days will turn blue [continuous] or yellow [event/motion detect]) or deselect
(days will turn gray [off]) the calendar days you wish to record.
1 3
P L A Y B A C K R E C O R D E D V I D E O ( c o n t i n u e d )
Playback Controls
T Play Back Record Files
1.
Go to MENU > LIVE VIEW.
2.
Left click a Live View window to bring up a shortcut toolbar and click on the
playback.
T Playback Controls
1.
Right click a Live Image to display a Quick menu and click on
icon for instant playback.
14
B A C K U P V I D E O R E C O R D I N G S A N D C L I P S
Back up recorded video clips to ensure important video is not lost or destroyed.
T Choose Recorded Video Clips To Back Up
1. Connect a USB flash drive, HDD, or DVD writer to an available USB port (this step is mandatory).
2. Go to MENU > PLAYBACK.
3. Select cameras for playback.
4. Select the date and beginning time of the incident.
5. Click START CLIPPING
button.
6. Select the ending time of the incident.
7. Click END CLIPPING
button (same button as START CLIPPING). Clip will be marked.
8. Repeat steps 1-6 as many times as required.
9. Click FILE MANAGEMENT
button to display a new window containing all marked clips.
10. Select the desired clips.
11. Click EXPORT to save files to the inserted USB device.
1 2
S E T U P R E C O R D I N G ( c o n t i n u e d )
4. Apply time settings as desired.
5. Press APPLY.
1
$
.
3
T Motion Detection Areas
To define the image areas that Motion Detection will monitor for each camera, do the following:
1.
Go to MENU > RECORDING CONFIGURATION > MOTION DETECT.
Use Camera pull-down menu to select camera to configure.
2.
3.
Check the Enable Motion Detection checkbox to enable motion detection.
4.
Use Sensitivity boxes to select how responsive detection should be (the more green boxes lit,
the greater the sensitivity).
5.
Drag a grid(s) over the area(s) on the image that will be sensitive to motion.
6.
Click the Settings Set button to configure Arming Schedule (when detection is enabled) and
Linkage Actions (what action(s) to take when motion is detected).
.
3
/
1
$
4
1 4
B A C K U P R E C O R D E D ( c o n t i n u e d )
.
3
/
14
$
T Lock Video Clips
1. Click on the images of the clips you want to lock.
icon for instant
2. Press the LOCK
button to prevent the file from being erased.
T Back Up Video Clips
1. Connect a USB flash drive, HDD, or DVD writer to an available USB port.
2. Click on the File Management button to display the File Management window.
3. In the File Management window, choose video clip(s) to back up and click Export button.
4. Choose backup device (USB flash drive, USB HDD, or DVD writer).
5. Click Export (to check backup, choose recorded file in Export interface and click
.
3
1 2
S E T U P R E C O R D I N G ( c o n t i n u e d )
T Record Quality
•
Main Stream
. TYPE
1.
Go to RECORDING CONFIGURATION > RECORD QUALITY > MAIN STREAM and set
Motion or Continuous (default)
the following items:
3 COLOR
- Stream Type enables/disables audio streaming from the cameras (if the camera does
/
Shows Recording Schedule days:
not have audio capabilities, Stream Type will have only Video option).
• Blue=Continuous
- Resolution sets recording resolution.
• Yellow=Event (motion/alarm)
• Grey=None
- Bitrate Type (Variable and Constant) saves HDD space when set to Variable.
$ TIMES
IP Cameras
Customize schedule times (ignore for
"motion only" recording)
/ ADD
Press to add time settings to
schedule
.
3
1 ENABLE SCHEDULE
If not checked, camera will not record
1
Analog Cameras
.
3
1
. CAMERA
Select camera
3 ENABLE MOTION DETECTION
Click to enable/disable
$ MOTION GRID
Draw grid area to detect motion
/ SENSITIVITY
Select # of green squares to set
- Video Quality adjusts picture clarity (high setting = four green squares is default).
sensitivity
Consider highest if hard drive space allows. Medium setting is a balance between good
1 SETTINGS/SET
picture and saving HDD space.
Configure arming schedule and
linkage actions
- Frame Rate sets recording frame rate (8 fps on continuous and 15 on motion by
4 APPLY
default). Higher frame rates require more storage, but allows better slow motion
Click to apply settings
playback.
- Max Bitrate Mode chooses between pre-set bitrate values and customized values
(General setting is default).
. CAMERA LIST
Select cameras to view
3 CALENDAR
Select dates to view
$ PLAY/STOP
Toggles between Play and Stop
/ START/STOP CLIPPING
Toggles between Start Clipping
and Stop Clipping
1 LOCK
Locks selected video clips to
prevent them from being deleted
4 FILE MANAGEMENT
Displays list of saved clips, export
clips from this window
button).
. VIDEO CLIPS LIST
Select desired clips to export
3 EXPORT BUTTON
Save clips to USB device
Hikvision USA Inc., 908 Canada Court, City of Industry, CA 91748, USA
Hikvision Canada, 4485 Dobrin, St-Laurent, Quebec, Canada, H4R 2L8
Telephone: +1-909-895-0400 • Toll Free in USA: +1-866-200-6690
E-Mail: [email protected] • www.hikvision.com
© 2017 Hikvision USA Inc. • All Rights Reserved
Specifications subject to change without notice. QSG DS-7716NI-I4/16P 032717NA
. MAIN STREAM
Select tab
3 CAMERA
Select IP camera
$ EVENT
For event recording only (motion
or alarm)
/ CONTINUOUS
For live view image and
continuous recording
/
$
1 VIDEO QUALITY
Select number of green squares
to set quality (in example,
sensitivity is set to 3)
. MAIN STREAM
Select tab
3 CAMERA
/
$
Select analog camera
$ EVENT
For event recording only (motion
or alarm)
/ CONTINUOUS
For live view image and
continuous recording
1 VIDEO QUALITY
Select number of green squares
to set quality (in example,
sensitivity is set to 3)