Garmin GPSMAP 8000 Series Kullanıcı El Kitabı - Sayfa 9

Deniz GPS Sistemi Garmin GPSMAP 8000 Series için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Garmin GPSMAP 8000 Series 43 sayfaları. Installation instructions
Ayrıca Garmin GPSMAP 8000 Series için: Kullanıcı El Kitabı (36 sayfalar), Hızlı Başlangıç Kılavuzu (4 sayfalar), Talimatlar Kılavuzu (15 sayfalar), Kurulum Talimatları Kılavuzu (14 sayfalar)

Garmin GPSMAP 8000 Series Kullanıcı El Kitabı
Collision Alarm: Sets the safe-zone collision alarm (Setting the
Safe-Zone Collision Alarm).
Display Setup: See Showing AIS and MARPA Vessels on a
Chart or on a 3D Chart View.
Laylines Settings
When in sailing mode (Setting the Vessel Type), you can
display laylines on the navigation chart. Laylines can be very
helpful when racing.
From the navigation chart, select Menu > Sailing > Laylines.
Display: Sets how the laylines and vessel are shown on the
chart, and sets the length of the laylines.
Sailing Ang.: Allows you to select how the device calculates
laylines. The Actual option calculates the laylines using the
measured wind angle from the wind sensor. The Manual
option calculates the laylines using manually entered
windward and leeward angles.
Tide Correction: Corrects the laylines based on the tide.
Fish Eye 3D Settings
NOTE: This feature is available with premium charts, in some
areas.
From the Fish Eye 3D chart view, select Menu.
View: Sets the perspective of the 3D chart view.
Tracks: Shows tracks.
Sonar Cone: Shows a cone that indicates the area covered by
the transducer.
Fish Symbols: Shows suspended targets.

Navigation with a Chartplotter

If your vessel has an autopilot system, a dedicated autopilot
control display must be installed at each steering helm in order
to disable the autopilot system.
The Auto Guidance feature is based on electronic chart
information. That data does not ensure obstacle and bottom
clearance. Carefully compare the course to all visual sightings,
and avoid any land, shallow water, or other obstacles that may
be in your path.
When using Go To, a direct course and a corrected course may
pass over land or shallow water. Use visual sightings, and steer
to avoid land, shallow water, and other dangerous objects.
NOTE: Auto Guidance is available with premium charts, in some
areas.
NOTE: Mariner's Eye 3D and Fish Eye 3D chart views are
available with premium charts, in some areas.
NOTE: The offshore Fishing chart is available with premium
charts, in some areas.
To navigate, you must choose a destination, set a course or
create a route, and follow the course or route. You can follow
the course or the route on the Navigation chart, Fishing chart,
Perspective 3D chart view, or Mariner's Eye 3D chart view.
You can set and follow a course to a destination using one of
three methods: Go To, Route To, or Auto Guidance.
Go To: Takes you directly to the destination. This is the
standard option for navigating to a destination. The
chartplotter creates a straight-line course or navigation line to
the destination. The path may run over land and other
obstacles.
Route To: Creates a route from your location to a destination,
allowing you to add turns along the way. This option provides
a straight-line course to the destination, but allows you to add
turns into the route to avoid land and other obstacles.
8
CAUTION
Auto Guidance: Creates a path to a destination using Auto
Guidance. This option is available only when using a
compatible premium chart in a compatible chartplotter. It
provides a turn-by-turn navigation line to the destination,
avoiding land and other obstacles. The navigation line is
based on the chart data and the safe depth, safe height, and
shoreline distance user-defined chartplotter settings. Using
these settings and chart data, the chartplotter creates a
navigation line that avoids all areas that cannot be navigated
between the present location and the destination.
When you are using a compatible Garmin autopilot
connected to the chartplotter using NMEA 2000
autopilot follows the Auto Guidance route.

Basic Navigation Questions

Question
How do I make the chartplotter
point me in the direction in
which I want to go (bearing)?
How do I make the device
guide me along a straight line
(minimizing cross track) to a
location using the shortest
distance from the present
location?
How do I make the device
guide me to a location while
avoiding charted obstacles?
How do I make the device
steer my automatic pilot?
Can the device create a path
for me?
How do I change the Auto
Guidance settings for my boat?
Destinations
You can select destinations using various charts and 3D chart
views or using the lists.
Searching for a Destination by Name
You can search for saved waypoints, saved routes, saved
tracks, and marine services destinations by name.
1
Select Info > Services > Search by Name.
2
Enter at least a portion of the name of your destination.
3
If necessary, select Done.
The 50 nearest destinations that contain your search criteria
appear.
4
Select the destination.
Selecting a Destination Using the Navigation Chart
From the Navigation chart, select a destination.
Searching for a Marine Services Destination
NOTE: This feature is available with premium charts, in some
areas.
The chartplotter contains information for thousands of
destinations offering marine services.
1
Select Info > Services.
2
Select Offshore Services or Inland Services.
3
If necessary, select the marine service category.
The chartplotter shows a list of the nearest locations and the
distance and bearing to each.
, the
®
Answer
Navigate using Go To. See Setting
and Following a Direct Course
Using Go To.
Build a single-leg route and navigate it
using Route To. See Creating and
Navigating a Route From Your
Present Location.
Build a multi-leg route and navigate it
using Route To. See Creating and
Navigating a Route From Your
Present Location.
Navigate using Route To. See
Creating and Navigating a Route
From Your Present Location.
If you have premium maps that
support Auto Guidance and are in
an area covered by Auto Guidance,
navigate using Auto Guidance. See
Setting and Following an Auto
Guidance Path.
See Auto Guidance
Line Configurations.
Navigation with a Chartplotter