Brother MFC 6490CW - Color Inkjet - All-in-One Bağlantı Kılavuzu - Sayfa 3

Yazılım Brother MFC 6490CW - Color Inkjet - All-in-One için çevrimiçi göz atın veya pdf Bağlantı Kılavuzu indirin. Brother MFC 6490CW - Color Inkjet - All-in-One 6 sayfaları. Quick setup guide - spanish
Ayrıca Brother MFC 6490CW - Color Inkjet - All-in-One için: Broşür ve Teknik Özellikler (9 sayfalar), Hızlı Kurulum Kılavuzu (48 sayfalar), Hızlı Kurulum Kılavuzu (48 sayfalar), Kurulum ve Kurulum (5 sayfalar), (İngilizce) Hızlı Yapılandırma Kılavuzu (48 sayfalar)

Sayfayı Yazdır

Brother MFC 6490CW - Color Inkjet - All-in-One Bağlantı Kılavuzu

MFC6490CW Vista Network Connection Repair Instructions

6. When the CONFIGURE PORT screen appears compare the IP address or Node Name with the IP

address or Node Name listed on the network configuration page printed in PART 2. If you receive an

error and cannot configure the port, close the error and the printer properties window and continue

to step 7.

a. If the IP address or Node Name is different continue to the next step. If the IP address or

node name is not different this issue is likely caused by other connectivity problems or

machine errors. Go to PART 7 to reestablish a network connection.

b. In the PRINTER NAME OR IP ADDRESS area enter the IP address or Node Name listed on the

network configuration page.

Click OK and this will return you back to the PRINTER PROPERTIES page.

d. Click on the GENERAL tab.

e. Click PRINT TEST PAGE.

A test page should now print correctly. If the test page prints, then the issue is resolved. If

the test page does not print, click OK and close the PRINTER PROPERTIES window. Right

click on the printer, then left click on CANCEL ALL DOCUMENTS and continue to Step 7.

7. Right click on the Brother driver and left click on PROPERTIES. The Brother printer driver properties

screen will now appear.

a. Click the PORTS Tab.

b. Click ADD PORT.

Choose STANDARD TCP/IP PORT then click NEW PORT. The Standard TCP/IP Printer Port

Wizard will appear.

d. Click NEXT.

e. In the field labeled PRINTER NAME OR IP ADDRESS, type the IP address of your Brother

machine from the Network Configuration sheet you printed in PART 2. Click NEXT.

A screen will appear with information about your Brother machine. Click FINISH.

g. Click CLOSE.

h. Click APPLY. Click the GENERAL TAB.

Click PRINT TEST PAGE. A test page should now print correctly. If the test page does not

print, click OK and close the PRINTER PROPERTIES window. Right click on the printer, then

left click on CANCEL ALL DOCUMENTS and continue to PART 7 to reestablish a network

connection.

PART 7: ESTABLISH A WIRELESS CONNECTION:

1. Before you begin, please gather the wireless network settings of your access point or wireless router.

This information can be found on the network configuration page of your wireless router or Access

Point. Please refer to the router or access point's user guide for instructions on accessing the

network configuration page. This information includes:

a. SSID (Service Set ID or Network name): Your Access Point or Wireless Routers are identified

by an SSID or Network Name.

b. Authentication (Open System or Shared Key)/Encryption Type (None or WEP)

WEP Key (If needed)

d. WPA/WPA2-PSK Encryption type (TKIP or AES) (If needed)

e. WPA/WPA2-PSK (Pre-shared Key) (If needed)

2. Verify the Wireless Router or Access Point is setup for DHCP. This setting is required in order for the

router or access point to broadcast a valid IP address to the device. Please refer to the user guide of

your wireless router or access point for additional information.

3. If the Brother machine was previously configured for wireless connection, continue to step 4. If the

machine was NOT configured for wireless connection, go to step 5.

4. If the Brother machine was previously configured for wireless connection the network settings need

to be reset before the unit can be configured for new wireless settings. Complete the following steps

to reset the Network Card.

NOTE: Resetting the network card will erase all current network settings.