Indesit IWE 7168 S Kullanım Kılavuzu - Sayfa 3

Yıkayıcı Indesit IWE 7168 S için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Indesit IWE 7168 S 16 sayfaları. Indesit washer user manual
Ayrıca Indesit IWE 7168 S için: Kullanım Kılavuzu (16 sayfalar), Kullanım Kılavuzu (16 sayfalar), Kullanım Kılavuzu (16 sayfalar), Kullanım Kılavuzu (16 sayfalar), Kullanım Kılavuzu (24 sayfalar)

Sayfayı Yazdır

Connecting the drain hose

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

We advise against the use of hose extensions; in case of

absolute need, the extension must have the same diameter

as the original hose and must not exceed 150 cm in length.

Ensure that if the drain hose is pushed into a standpipe, that

the end does not go down more than 15cms (6 inches). If the

hose is pushed down too far, this may cause the machine to

self -syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains socket, make

sure that:

• the socket is earthed and in compliance with the appli-

cable law;

• the socket is able to sustain the appliance's maximum

power load indicated in the Technical details table (see

page 5);

• the supply voltage is included within the values indicated

on the Technical details table (see page 5);

Connect the drain hose, wi-

thout bending it, to a draining

duct or a wall drain situated

between 65 and 100 cm

from the floor;

The drain hose may be

connected to an under-sink

trap. Before connecting the

drain hose from the machine

ensure that any blanks or

removable ends have been

taken off the spigot.

If it is place over the edge of

a basin or sink be sure the

free end of the hose should

not be underwater.

• the socket is compatible with the washing machine's plug.

If this is not the case, replace the socket or the plug.

Your appliance is now supplied with a 13 amp fused plug

it can be plugged into a 13 amp socket for immediate use.

Before using the appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED

OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved fuse

to BS 1362 should always be used, and the fuse cover re-

fitted. If the fuse cover is lost, the plug must not be used until

a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the correct

colour as indicated by the coloured marking or the colour that

is embossed in words on the base of the plug. Replacements

can be obtained directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug and you

should wish to re-route the mains cable through partitions,

units etc., please ensure that either:

the plug is replaced by a fused 13 ampere re-wearable plug

bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable outlet,

controlled by a switch, (in compliance with BS 5733) which

is accessible without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make

the pins unusable so that it cannot be accidentally inserted

into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured in accor-

dance with the following code:

Green & Yellow

Earth

Blue

Neutral

Brown

Live