Aqua Cooler AC-CURVE-CT-HC Kullanım ve Bakım Kılavuzu - Sayfa 5

Su Sebili Aqua Cooler AC-CURVE-CT-HC için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu indirin. Aqua Cooler AC-CURVE-CT-HC 7 sayfaları.

Sayfayı Yazdır

• Knob: The user can turn the knob to select the temperature. The temperature value will be according to

[normal temperature] (inlet water temperature value)—>[ 45°C ]—>[ 50°C ]—>[ 55°C ]—>[ 60°C ]—>[ 65°C]

—>[ 70°C ]—>[ 75°C ]-->[ 80°C ]—>[ 85°C ]—>[ 90°C ]—>[ 100°C ]—>[ CO ] (cold water) for sequential

cycles, and the corresponding selection will be shown on the display panel. Each time the temperature is

selected, the buzzer emits a short "ding" sound. The display panel will show the last setting status at standby

mode; if the appliance power reconnected, it will restore the factory settings to the [normal temperature]

stage.

• Water Extraction Key: In the unlocked state, touch the water extraction key [

temperature, the appliance dispenses water according to the selected water temperature and water volume,

the corresponding function key will light up in white when dispensing water, and the panel will display the

corresponding water temperature and water volume icon. After dispensed, the water extraction key light will

off. The user can touch the water key [

] to stop the operation, and touch the water extraction key [

again to dispense water according to the selected water temperature and water volume

Reminder: Each time the function key is touched, the buzzer emits a short "ding" sound.

• Refrigeration Indicator: When the refrigeration indicator shows on the display panel, it indicates the

appliance at refrigeration state; after completed, the refrigeration icon will light off.

• Antibacterial Function: When starting to dispense water, UVC-LED to sterilize the water in the pipeline

automatically, turns on the white LED indicator lamp, and displays the "UV" indictor on the display panel at

the same time. After that, the white LED indicator lamp and the "UV" indicator light will off.

Water Shortage Reminder

When the system detects that the water level has reached the lowest water level, the appliance will start the

water shortage protection automatically; at this time, the water pump and heating body will stop the operation,

the water shortage indicator on the display panel will flash and the buzzer will sound 5 times.

After filling the water, tap the water button [

] at the unlocked state, the water pump will detect the water

level again and the water shortage indicator on the display panel will light off. After completion, the product will

resume normal operation.

CAUTION! After dispensed, user must wait until no remaining water discharge before taking out the cup,

otherwise, you may be scalded by the remaining water.

Reminder

If the water tank is out of water during operation, no water will discharge while warning signal emits. To

resume, add sufficient water to the water tank.

Attention! If there is remaining water, it is recommended to clean up first to avoid overflow.

During heating and refrigeration, there will be slight noise come out from the product and the pump, this

is normal situation.

The boiling time varies due to ambient and water temperature. (The boiling time will be extended if the

water temperature is low).

Your Partner in Cool.

] after selecting the

] once

TROUBLESHOOTING

Check the following before calling for servicing.

Symptoms

Checking Points

The product cannot

Check if the dispenser is well

switch on

connected with power supply.

Loose internal connections/parts.

Button does not

The appliance is in a locked

respond

state.

Circuit control failure.

Cannot extract

Too much scale or impurities in

water

the appliance.

The hot water

Too much scale or impurities in

temperature is not

the appliance.

high enough

Abnormal circuit control function.

Abnormal power supply voltage.

Error Code El

Heating element overheats.

Error Code E2

The inlet water temperature

exceeds 40°C.

Error Code E3

Outlet water temperature sensor

failure.

Error Code E4

Water inlet temperature sensor

failure.

If the above remedies / solutions cannot fix the problem, unplug the appliance immediately, note the error code

and report it to Aqua Cooler for checking and repairing. To avoid any danger and damage to the appliance, do

not disassemble or repair it by yourself.

Remedy

Check if the dispenser is well connected with

power supply.

Check if the power switch is turned on.