Aqua Quip QC Series Kurulum Talimatları ve Kullanım Kılavuzu - Sayfa 3
Yüzme Havuzu Aydınlatması Aqua Quip QC Series için çevrimiçi göz atın veya pdf Kurulum Talimatları ve Kullanım Kılavuzu indirin. Aqua Quip QC Series 4 sayfaları. Surface-mounted led retro-fit pool light
Ayrıca Aqua Quip QC Series için: Kurulum Talimatları ve Kullanım Kılavuzu (4 sayfalar)
Sayfayı Yazdır
E) Once the Female Plug is pushed all the way into the Connector Housing, then the Cable Nut must be
tightened to ensure a leakproof seal. Hold the "hex" area on the Connector Housing with multi-grips or
spanner and tighten the Cable Nut until the Seal compresses around the cable. Ensure that the Washer
remains "clipped" in the Cable Nut when tightening, this will ensure the Seal is compressed effectively.
Female Plug is pushed down all the way,
and Cable Nut is tightened.
F) The Quick Connect Plug Kit is now ready to be
inserted into the receptacle on the rear of the new
QC Series LED light. The two O-rings are factory-
lubricated, ensure they are free from dust and grit.
Align the Female Plug with the exposed metal pins in
the receptacle and push into place. Push the Cable
Bracket towards the light until the clips engage into
place. Use a #1 Phillips screwdriver and 3 x stainless
steel screws provided and affix the Cable Bracket into
the three screw holes. Do not overtighten.
G) Wind up excess cable around the hooks on the rear of the QC Series LED light. Use the three PE6 screws
provided to mount the QC Series LED Pool Light onto the three posts on the Universal Mounting Bracket.
Important Information for Installer and Pool Owner
Pool light must be fully submerged before switching on. If the light overheats due to operation out of
water, the inbuilt "run dry" thermal cut-out will engage and the LEDs will operate at a greatly reduced
intensity until power is shut down for 5 minutes and turned back on.
Always allow sufficient cable length behind the pool light to enable future servicing.
Only use stainless steel screws provided, using inferior quality screws voids the warranty.
Internal components are not user-serviceable. Return to place of purchase for service.
Never stare directly at LED lights, prolonged direct exposure can cause eye damage.
TECHNICAL SPECIFICATIONS AQUA-QUIP QC SURFACE MOUNTED LED POOL LIGHTS
Power Requirement for Fixed Colour and
Multi-Colour LEDs:
Pool Light Protection Rating: IPX8 to 2.0m depth.
Temperature Range:
Installation Location:
Power Consumption
(Fixed Colour LEDs):
Power Consumption
(Multi-Colour LEDs):
Rated Lamp Life:
Voltage Tolerance (Fixed Colour and
Multi-Colour LEDs):
Light Colour:
Light Output (Typical):
Fault Protection:
QC SERIES SURFACE MOUNTED LED RETRO-FIT POOL LIGHTS – INSTALLATION INSTRUCTIONS & OWNERS MANUAL
QC SERIES
Hex Area
12V ~ 32V AC 50/60Hz.
-10°C ~ +40°C pool water temperature.
200mm ~ 400mm below water level.
Maximum 16VA at all voltages 12V ~ 32V.
Maximum 22VA at all voltages 12V ~ 32V.
>50,000 hours.
10.5V AC ~ 35V AC.
White = >5000K, Blue = 475nm, Green = 525nm.
White = 1050 Lumens, Blue = 300 Lumens, Green = 650 Lumens.
Power Cycle "Run Dry" thermal cut-out. Voltage transient clamping.
SURFACE MOUNTED LED
RETRO-FIT POOL LIGHT
Washer remains clipped in the rear
of the Cable Nut.
QC Surface Mounted Pool Light Dimensions
Washer
230mm
67mm
3