DH Instruments 3367797 Talimat Sayfası
Kablolar ve konektörler DH Instruments 3367797 için çevrimiçi göz atın veya pdf Talimat Sayfası indirin. DH Instruments 3367797 2 sayfaları. Interconnection kit for mpg2-h with rpm4 or pg7302
Sayfayı YazdırInterconnection kit for MPG2-H with RPM4
or PG7302, P/N 3367797, includes:
DESCRIPTION
Nipple, 2.75 in.
(70 mm), DH500
Nipple, 6 in.
(152 mm), DH500
Nipple, 12 in.
(305 mm), DH500
Nipple, 5 in. x 1/8
in.(127 mm x 3 mm),
DH500, flexible
Elbow DH500
Tee DH500
Union DH500
Plug DH500/DH700
Adaptor, DH500F x
1/8 in. (3 mm) NPTM
Introduction
This kit provides the tubing and fittings necessary to
connect an MPG2-H pressure controller to either an
RPM4 reference pressure monitor or to a PG7302
piston gauge, and also to a device under test. This
document contains instructions for connecting the
fittings and tubing.
Installation of Interconnections
Remove Plugs from MPG2-H, Tee, Union and
RPM4 or PG7302: Unscrew the glands from the
test ports of the MPG2-H and RPM4 or PG7302.
Remove the collar and plug from inside each
gland. There should be one stainless steel plug.
The plastic plugs will not be used.
stainless steel plug.
Install glands and collars onto flexible 5 in.
nipples and 2.75 in. nipple: Slide a gland over a
nipple so that the threads of the gland face
outward. Next, screw a collar onto the nipple by
turning it to the LEFT. Allow two nipple threads to
show between the collar and nipple tip. Use
collars and glands from tee, elbow and union.
PRESSURE
QTY
PART NO.
RATING
500 MPa
1
3068887
(72,500 psi)
500 MPa
1
3068893
(72,500 psi)
500 MPa
1
3068902
(72,500 psi)
200 MPa
2
3126068
(30,000 psi)
400 MPa
1
3068361
(60,000 psi)
400 MPa
1
3068501
(60,000 psi)
400 MPa
1
3068520
(60,000 psi)
700 MPa
1
3068470
(100,000 psi)
200 MPa
2
3068785
(30,000 psi)
Keep the
Interconnection Kit
MPG2-H with RPM4 or PG7302
For
Instruction Sheet
RPM4 – Install glands and collars onto the
a
12 in. nipple.
PG7302 – Install glands and collars onto the
b
6 in. and 12 in. nipples and install both nipples
into union.
Orientate weep holes on union, tee,
and elbow facing up to facilitate
leak check and purge.
Install nipples into three way tee and elbow:
Install the 2.75 in. nipple into the center port of the
three way tee. Install the 12 in. nipple (or 6 in. and
12 in. nipple assembly with union) into either of the
end ports on the three way tee as shown in Figure 1.
Install 5 in. flexible nipple into elbow. Install 12 in. or
6 in. nipple from tee into elbow. Tighten the nipples
with a 5/8 in. wrench or crescent wrench. The
flexible 5 in. nipple connects to the MPG2-H. The
2.75 in. nipple in the center of the tee connects to
the RPM4 or to the PG7302. In Figure 1 the left port
is currently plugged, but the remaining flexible 5 in.
nipple can be installed in the left port and connect to
the DUT.
Optional: Extend the front feet on RPM4: The front
feet of the RPM4 can be extended so that the RPM4
is inclined for easier reading and display access.
RPM4 A70M or less - Install NPT adaptor into
RPM4.
(10,000 psi) or less have 1/8 in. NPTF test ports.
These ports require the use of one of the DH500F
by 1/8 in. NPTM adaptors. Wrap Teflon
tape around the NPT threads of the adaptor three
times, and install the adaptor into the RPM4.
Install the free end of the center nipple into
RPM4 or PG7302:
should be inserted into the test port of the RPM4 or
PG7302. Screw in the gland loosely by hand. Do
not tighten the gland in the RPM4 or PG7302 yet,
since it will be tightened when the system is primed.
Install the 5 in. nipple into the MPG2-H. Screw
in the glands loosely by hand. Tighten the gland
with a 5/8 in. wrench or crescent wrench.
Install a DH500M to 1/8" NPT male adaptor in
the DUT if necessary: The 1/8 in. NPT male
adaptor can be used to connect the remaining
flexible 5 in. nipple to DUTs with 1/8 in NPT
female ports. If you intend to use the adaptor,
P/N 3367797
Note
RPM4s that have ranges of 70 MPa
The center, 2.75 in. nipple
®
thread