Avtron HS35A Talimatlar Kılavuzu
Medya Dönüştürücü Avtron HS35A için çevrimiçi göz atın veya pdf Talimatlar Kılavuzu indirin. Avtron HS35A 7 sayfaları. 1/2 inch to 1 inch [12mm-25mm] hollow shaft
Sayfayı Yazdır
Nidec-Avtron Makes the Most Reliable Encoders in the World
8 9 0 1 E . P L E A S A N T VA L L E Y R O A D • I N D E P E N D E N C E , O H I O 4 4 1 3 1 - 5 5 0 8
T E L E P H O N E : ( 1 ) 2 1 6 - 6 4 2 - 1 2 3 0 • F A X : ( 1 ) 2 1 6 - 6 4 2 - 6 0 3 7
E - M A I L : t a c h s @ n i d e c - a v t r o n . c o m • W E B : w w w . a v t r o n e n c o d e r s . c o m
DESCRIPTION
The Avtron Model HS35A Hollow Shaft Rotary Incremental Encoder is a
speed and position incremental transducer (also known as tachometer
or rotary pulse generator). When mounted to a motor or machine, its
output is directly proportional to shaft position (pulse count) or speed
(pulse rate). The HS35A operates down to zero speed and can be used
for both control and instrumentation applications.
The HS35A employs a hollow shaft and clamping collar to lock the
encoder to the shaft. A high-performance resin hollow shaft insert
provides electrical isolation from motor shaft currents and permits
models to fit a broad range of shaft sizes from 1/2" to 1" [12mm -
20mm]. An anti-rotation bracket prevents rotation of the encoder while
allowing for shaft end float and axial movement. An optional protective
basket kit offers additional protection from impact and motor lifting
damage.The HS35A encoder offers 2Ø outputs (A,B) 90° apart for
direction sensing (A Quad B), with complements (A,B) and with
marker pulse and complement (Z,Z)
INSTALLATION CONSIDERATIONS
See page 3 and drawing on last page for shaft engagement rules.
Shaft may include keyway, but should not be flatted.
The HS35A offers optional Avtron flexible anti-rotation tethers/
brackets which will permit the encoder to tolerate ±0.1" of shaft end
float/axial movement. Select the proper tether for the application from
the table below.
CAUTION
Be careful not to damage clamping fingers of hollow
shaft during handling. Do not tighten clamping collar
before installation onto motor shaft.
HS35A PART NUMBERS AND AVAILABLE OPTIONS
Line
Model
PPR
Driver
HS35A
1- 5-28V
G- 100
5- 2500
(7272)
K- 200
8- 4000
2- 5-28V,
L- 240
D- 4096
open
M- 250
9- 5000
collector
Q- 500
0-
Special
(7273)
R- 512
4- 5-28V in,
S- 600
5V out
W- 1000
(7272)
Y- 1024
Z- 1200
3- 2000
4- 2048
«
Only available with MS 6 and 7 pin connectors
All dimensions are in inches [millimeters].
Specifications and features are subject to
change without notice.
*Requires option code "00W"
.
Bore Options
Connector Options
0- Non-std.
Q- 14mm
W- 18" flex. cable
B- 1/2
R- 15mm
Y- 18" flex. cable BEI
C- 5/8"
S- 16mm
wire colors
D- 3/4"
V- 19mm
E- 7/8"
W- 20mm
F- 1"
Y- 25mm
P- 12mm
U- Universal 1/2" to
7/8"
(all U.S. inserts)
Z- Universal 12mm to
20mm
(all metric inserts)
10 Pin MS
A- w/o plug (std. phasing)
E- w/o plug (std. phasing)
B- w/o plug (Dynapar
F- w/o plug (Dynapar
HS35 phasing)
HS35 phasing)
C- "A" w/ plug
G- "E" w/ plug
D- "B" w/ plug
H- "F" w/ plug
HS35A
Equipment Needed for Installation
Provided
HS35A Encoder
Clamping Collar
WARNING
Installation should be performed only by qualified
personnel. Safety precautions must be taken to ensure
machinery cannot rotate and all sources of power are
removed during installation.
WARNING
Be certain to identify thread locker and anti-seize
compound correctly. Using anti-seize in place of
thread locker can cause mechanical failure leading to
equipment failure, damage, and harm to operators.
Mounting
Protection
Style
U- Universal
0- None
End-of-Shaft
1- Basket
& Thru Shaft
Connector Options
6 Pin MS
7 Pin MS
J- w/o plug (std. phasing)
K- w/o plug (Dynapar
HS35 phasing)
M- "J" w/ plug
N- "K" w/ plug
1
Encoder
Instructions
HS35A
1/2" to 1" [12mm-25mm]
HOLLOW SHAFT
Optional
Not Provided
Anti-Rotation
#2 Phillips Screwdriver
Tether Kit
5/32" Hex Wrench (US)
Shaft Sizing Insert
3mm Hex Wrench (Metric)
(T-Handle Style)
Mating MS Cable
Connector
Caliper Gauge
Dial Indicator Gauge
Protective Basket Kit
7/16", 9/16", 5/8", 3/4", 10mm
Wrenches (tether options)
Anti-Rotation
Channels
Tether Options
–
X- None
A- A,A
,B,B
–
A- Fan cover, 1/4-20
Z,Z
–
B- Fan cover, 5/16-18
B- A,A
,B,B
–
C- Fan cover, 3/8-16
«
D- A,A
D- Fan cover, all
E- A,B,Z
E- 4.5" or 6.75" C-Face
«
F- A,B
F- 8.5" C-Face
M- 4.5" C-Face or Fan
Cover
R- Pin and block
U- Universal
(all tether options)
8 Pin M12
10 Pin Mini-twist lock*
T- w/o plug (Turck Pinout)
R- 10 pin mini twist lock
U- w/o plug (US Pinout)
S- 10 pin mini twist lock
Special
Features
–
000- None
,
9xx- Specify
–
«
cable length
xx=feet (use w/
option "W")
«
00W- Connector
on cable
w/o plug (bulkhead)
on cable*