Dell PowerConnect 6224 Yayın Notu - Sayfa 20
Anahtar Dell PowerConnect 6224 için çevrimiçi göz atın veya pdf Yayın Notu indirin. Dell PowerConnect 6224 34 sayfaları. Powerconnect 6200 series
Ayrıca Dell PowerConnect 6224 için: Teknik Özellikler (2 sayfalar), Planlama ve Hazırlık Kılavuzu (12 sayfalar)
Sayfayı Yazdır
Description
Bridge multicast forbidden
forward-unregistered causes
L3 Multicast to fail.
Cut-through mode command
help is not clear.
Console logging levels help
does not indicate precedence.
Web Dot1x Authentication Max
Users show units in seconds
vs. # Users.
Web and CLI disagreement on
Dot1x statistics.
ReFormatFlashFileSystem no
available via the boot menu.
Show interfaces advertise
ethernet <unit> <port>
command is not parsed
properly.
Stack port link status mismatch
in CLI and Web interface when
configured for Ethernet.
Web Home > General > Asset
selection does not show
details.
Mirroring port should not send
CDP packets.
Backups with SNMP do not
work correctly.
END command with all upper
case is not understood by CLI.
Trying to add ninth member to
a channel-group shows LACP
assignment in HTTP view.
Switchport protected name
accepts non-alphanumeric
characters.
Description inconsistency
between HTTP and CLI
Administration.
Inconsistent CLI and Web
interface responses for STP
LAG settings.
Ip host parse
18
User Impact
Flooding in ingress VLAN.
For normal command and no command
the help information is the same.
Help content needs to show severity level
of logging.
Incorrect help string added in read-only
page of dot1x, causing user confusion.
Not displaying the MAC address correctly
in the field Last Frames Source in the
web page EAP Statistics.
ReFormatFlashFileSystem cannot be
executed from boot menu.
Show interfaces advertise ethernet <unit>
<port> command is not parsed properly.
To display the correct link status when
configured stack mode is Ethernet in the
Stack Port Summary web page.
Incorrect link for Asset page on General
Index page.
Both mirrored and mirroring ports are
sending CDP packets.
The MIB allows users to backup the
starting configuration to TFTP using
SNMP, but the file is corrupted.
User will not be able to go to root mode
by entering END.
Trying to add ninth member to a channel-
group shows LACP assignment in HTTP
view.
Needed to check that protected port name
accepts only alphanumeric characters.
Spaces were not accepted in description
fields through web.
Inconsistent CLI and Web interface
responses for STP LAG settings.
Some ip host names with numbers and
periods are rejected.
Resolution
Modified the L3 interaction code of
snooping to notify the driver when
snooping is enabled. When
snooping is disabled, the current
operational state of snooping is also
sent to the driver.
Changed the help information
Added the severity levels to the help
strings.
Removed help string for read-only
page of dot1x.
Corrected the problem in the object
handler.
The ReFormatFlashFileSystem
operation is now available via the
boot menu.
Added a check for invalid interface.
Corrected the web page to properly
handle Ethernet and show link
status as up.
Corrected the file name for the
Asset page.
Get probe events, and mark
interface as acquired in ISDP
database. As a result, ISDP does
not participate on this port.
Corrected handling of upload
filetypes and setting local filename
in SNMP.
Use case insensitive comparison.
Corrected the code to enable LACP
after ports are added to lag
successfully.
Enhanced the validation.
Added appropriate validation.
Use the CLI formatting such that
both the CLI and Web are in sync.
Corrected the host name checks.
System Firmware Version 3.2.0.6