Epever LS LPLI Series Manuel

Kontrolör Epever LS LPLI Series için çevrimiçi göz atın veya pdf Manuel indirin. Epever LS LPLI Series 2 sayfaları. Solar charge controller with built-in led driver

Sayfayı Yazdır

HUIZHOU EPEVER TECHNOLOGY CO., LTD.

Thank you for selecting the LS LPLI series solar charge controller

with built in LED driver. Please read this manual carefully before

using the product and pay attention to the safety information.

Solar Charge Controller

1. Overview

The LS LPLI series controller combines the solar charge controller and LED constant

current driver in one unit. It is ideal for solar LED lighting, especially for the LED lamp

application, which requires dimmer function. The advanced pulse width modulation

charging methods enables system charging and discharging management to obtain the

most radical optimization. Make the system cost reduce and increase system flexibility.

Features:

 Apply to lead-acid battery and lithium battery

 Lithium battery self-activating function

 Lithium battery low-temperature protection function

 Intelligent power mode with 365-day lighting control technology

 Load power reduction automatically

 Load power limitation function

 Maximum output efficiency of 96%

 Digital precision constant current control and the control accuracy are less than±2%

 Discharging power calculation and real-time energy statistics recording function

 Configurable multiple load control modes, LED rated current, and the current

percentage

 Load test function for detecting the system

 Extensive electronic protections

 Without any button, parameter setting via RC-10 and FC-01 with IR function.

 Fully encapsulated PCB, IP68 protection

 Aluminum housing for better cooling

2. Product Features

❶

Charging Status LED indicator

❷

Battery Status LED indicator

Temperature Sensor ※

❸

❹

PV Positive and Negative Wires

※ If the temperature sensor connection is short-circuited or open-circuit, the

controller charges or discharges the battery at 25℃ and no temperature

compensation.

3. Wiring

 Reference for Serial connection of LED

System

Serial

Voltage

connection

5～18 LED

12V

24V

10～18 LED

 DO NOT electric shock! With the built-in boost LED driver, the output

voltage is higher than the human safety voltage.

 If the LED connection number is wrong, the load or controller is

WARNING

damaged.

The above LED (1W, 3.3V) is calculated. If the user uses the

unconventional LED, The actual LED voltage must less than the Max. Load

CAUTION

Output Voltage.

 Connection Order

1) Connect components to the charge controller in the sequence, as shown in Figure 2

Wiring, and pay much attention to the "+" and "-." Please don't insert the fuse or turn on

the breaker during the installation. When disconnecting the system, reverse the order.

2) After powering on the controller, check the controller's battery LED indicator; it usually is

green. Otherwise, please refer to chapter 8.

3) Connect a fuse in series through battery positive (+) in the circuit. The battery circuit

fuse must be 1.25 to 2 times the rated current. The installed distance is within 150mm.

 Load self-test function

The load is ON when the controller power on for 10 seconds. After 10 seconds, it restores

the working mode setting.

---with built-in LED Driver

Figure 1 Product Feature

❺

Battery Positive and Negative Wires

❻

Load Positive and Negative Wires

❼

Infrared Receiver Module

❽

Infrared LED

Min. Output

Max. Output

Voltage

15V

30V

Tel：+86-10-82894896/82894112/+86-752-3889706

4. LED Indicators

Indicator

All

indicators

5. Load Working Mode

1) Manual Mode

2) Light ON/OFF(default)

3) Light ON + Timer

Light ON + Timer1

Light ON + Timer2

60V

Light ON + Timer3

Item

LED Rated Current

Timer1

LED Rated Current Percentage

Timer2

LED Rated Current Percentage

Figure 2 Wiring

Color

Status

Green

On Solid

Green

Slowly Flashing(1Hz)

Green

Fast Flashing(4Hz)

Green

OFF

Green

On Solid

Green

Slowly Flashing(1Hz)

Green

Fast Flashing(4Hz)

Orange

On Solid

Red

On Solid

Red

Slowly Flashing(1Hz)

Green and

Flashing two times

orange

Turn-On voltage (Adjustable):

5V(12Vsystem), delay10min.

Turn-Off voltage (Adjustable):

6V(12Vsystem), delay10min.

Note: 24V system voltage×2

Default※

Mode1

Mode2/3

0.35A

100%

80%

50%

Website：www.epever.com

Instruction

PV connection normal but low

voltage(irradiance) from PV, no

charging

In charging

PV reverse polarity

No PV voltage(night time) or PV

connection problem

Normal

Full

Over voltage

Under voltage

Over discharged

Battery Overheating

Set parameters successfully

Range

0-2.6A(LS101240LPLI)

0-2.0A(LS102460LPLI)

0-4.0A(LS101260/2024120LPLI)

00:00—23:59H

0—100%

00:00—23:59H

0—100%