Architectural Mailboxes elephantrunk 6950 Manuel

Saklama Kutusu Architectural Mailboxes elephantrunk 6950 için çevrimiçi göz atın veya pdf Manuel indirin. Architectural Mailboxes elephantrunk 6950 2 sayfaları. Parcel drop

Sayfayı Yazdır

Always home. Even when you're not.

elephantrunk

parcel drop

Carefully unpack the elephantrunk, parts and hardware.

Hardware and Parts (included)

x 1, mounting bolt

x 1, lag shield

(for hardscape

installation only)

x 4, leveling feet

This address is equipped with an

elephantrunk

parcel drop

location:

www.architecturalmailboxes.com

Architectural Mailboxes, LLC, 2012. Rev I

x 1, placard

x 2, Master Keys

Choose where to locate your elephantrunk

NOTE: The elephantrunk parcel drop is NOT intended to replace a mailbox. Its primary

purpose is to receive parcel deliveries.

 The courier must be able to freely access your elephantrunk to make deliveries.

 Choose a protective location, such as on a porch or under an eave, and away from sprinklers.

 You can anchor your elephantrunk to a hardscaped or wooden surface. It will require drilling a hole into the surface, so make sure you

pick the right location.

elephantrunk installation

Place your elephantrunk at the desired location with

the help of another person.

Open the lid and mark the ground

through the hole in the floor.

Make sure back of mailbox is at

least 3 inches from any walls to

ensure proper door operation.

After marking the ground, place

the elephantrunk aside before

continuing.

Drill a hole where you marked the ground:

For hardscape (for example, stone walkway or concrete pad),

drill a hole 2.5" deep at the mark with a 5/8" masonry bit.

For wood (for example, deck or porch), drill a pilot hole 2"

deep at the mark using a 1/4" wood bit.

5/8" hole

1/4" hole

2.5" for lag

shield

We're all ears!

Give us a call at (800) 464-7491 or email

[email protected] with any questions.

Tools (not included)

Drill suitable for drilling into masonry or wood

x 1, washer

Hex wrench

- or -

x 4, placard screws

5/8" masonry drill bit

(if installing on hardscape)

1/4" wood drill bit

x 1, mounting knob

(if installing on wood deck/porch)

For hardscape:

For wood:

Remove any debris

Screw the

from the hole and insert

mounting bolt

directly into the

the lag shield so it is

flush with the surface.

surface.

Screw the mounting bolt

into the lag shield.

Use the hex portion at the

center of the bolt to screw

it into the hole.

For both installations,

screw it all the way so the

hex portion is touching

the surface.

2.0" for

wood

Model 6950

Carefully screw the four

leveling feet into the bottom of

each leg about half way.

With help, lift the elephantrunk

over the installed bolt, aligning

the bolt through the hole in the

floor. DO NOT secure in place

with the mounting knob yet.

Level the elephantrunk by adjusting the feet up

and down.

elephantrunk use

Master Keys: These allow you to open the unit as well as access other features that need to be protected, such as

reprogramming the keypad code, replacing batteries and changing modes of operation. MAKE SURE YOU KEEP THESE KEYS

IN A SAFE PLACE AND DON'T GIVE THEM OUT TO OTHERS.

Installing Batteries

(4xAA - not included):

Phillips head

screwdriver

Resetting the Keypad Code:

Unlock the unit using the Master Key. This

exposes the red programming button on

the back of the lock assembly without

taking the battery cover off. The lock must

be in the unlocked (vertical) position to

reveal the red programming button.

Daily Operation:

To unlock the your elephantrunk using the keypad, input your 4 digit code followed by the # key. This places it in

Normal Standby Mode described further below. Your elephantrunk can be used in three different modes....

Normal Mode (factory setting)

If you are expecting a delivery, enter the keypad code

when leaving for the day. This will unlock the unit and tell it

to wait for a delivery. When the carrier opens the lid and

delivers the parcel, the unit senses this activity and will

automatically engage the lock so your delivery is safe until

you return home.

Alternatively, you can give your keypad code to carriers so

they can enter it and gain access to the unit. This is useful

if you are expecting more than one delivery during the day

and want to allow delivery of all of them, limited only by the

capacity of the storage compartment. You can give out the

code by entering it into the address line when you order

goods (e.g., "Parcel Box Code 1234"). Some carriers also

allow you to enter a "Gate Code" into your online profile

that can be stored and updated at any time. Check in your

online profile if you subscribe to these carriers' services.

After delivery, you can retrieve your parcel(s) from the unit

by entering your keypad code or by using your Master Key.

You can also leave outgoing return-service parcels in the

unit for retrieval by the carrier.

Rev. D

Place the washer over the bolt and screw on the mounting

knob. The knob only needs to be hand tightened.

Place the cushion onto the floor over the mounting knob.

Remove protective plastic coating from the placard and

write the location of your elephantrunk onto the placard

with a permanent marker.

Attach the placard to your front entry in a conspicuous

location so the courier knows where to deliver your items.

Using a Master key, place the

Remove this screw to access the

lock in unlocked (vertical)

battery compartment.

position.

Rear View

of Lock Assembly

Rear View

of Lock Assembly

Always Locked Mode

This mode locks the units and deactivates the keypad. This is useful, for example, if you

are leaving for vacation and don't want anyone to access the unit. To set the unit into

Always Locked Mode:

1) Unlock the unit using the Master Key.

2) Unscrew and remove the battery cover on the back of the lock assembly.

3) Locate the small blue switch and move it to the left of the unit as viewed from the rear.

4) Screw the battery cover back on, lock the unit and remove the Master Key.

Never Locked Mode

This mode unlocks the unit and deactivates the keypad. This is useful if you want to allow

full access to the unit all the time by anyone. To set the unit into Never Locked Mode:

1) Unlock the unit using the Master Keys.

2) Unscrew and remove the battery cover on the back of the lock assembly.

3) Locate the small blue switch and move it to the right of the unit as viewed from the rear.

4) Screw the battery cover back on, close the unit and remove the Master Key.

Always Locked Mode

(blue switch in left position)

(blue switch in center position)

Over tightening with a tool may damage

the floor and invalidate your warranty.

Insert batteries as shown, replace

battery cover, place the lock in locked

(horizontal) position, and remove

Master Key.

Using a small implement like a pencil, depress the

programming button. Within 60 seconds, enter a new

4-digit code using 0 through 9, then press #. Test your

new code by closing the lid (it does not need to be

locked but lid must be closed) and input your code

followed by the # key. If your code works, the keypad

will show the green light flash twice with two beeps. If

your code does not work, the keypad will display the

red light and have a long beep sound. If this occurs, try

to reset code again.

Never Locked Mode

(blue switch in right position)

Normal Mode