Epson 6110i - PowerLite XGA LCD Projector Kullanıcı Kılavuzu - Sayfa 7

Projektör Epson 6110i - PowerLite XGA LCD Projector için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Epson 6110i - PowerLite XGA LCD Projector 17 sayfaları. Release of emp ns connection for windows & mac upgrade from v2.50 to v2.51
Ayrıca Epson 6110i - PowerLite XGA LCD Projector için: Kullanıcı Kılavuzu (42 sayfalar), Kullanım Kılavuzu (36 sayfalar), Kullanım Kılavuzu (47 sayfalar), Teknik Özellikler (2 sayfalar), Tamamlayıcı Kılavuz (1 sayfalar), Hızlı Kurulum Kılavuzu (7 sayfalar), Kullanıcı Kılavuzu (1 sayfalar), Parça Listesi (1 sayfalar), Uygunluk Beyanı (4 sayfalar), Ürün Destek Bülteni (25 sayfalar), Ürün Destek Bülteni (22 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (41 sayfalar), Ürün Destek Bülteni (15 sayfalar), Ürün Destek Bülteni (22 sayfalar)

Sayfayı Yazdır

Epson 6110i - PowerLite XGA LCD Projector Kullanıcı Kılavuzu

2. If necessary, you can fine-tune the height by turning the

projector's front feet without lifting the front of the

projector.

Raising the projector causes the image to become "keystone"

shaped, but you can correct the distortion by pressing the

buttons on the projector as described in the next

section.

Adjusting the Image Shape

In most cases, you can maintain a square or rectangular image

by placing the projector directly in front of the center of the

screen with the base of the lens level with the bottom of the

screen.

If the projector is slightly tilted (within a range of 30° up or

down), you can use the

Keystone

control panel or the projector's Keystone menu (see "Using

Keystone Correction" on page 7) to correct vertical keystone

distortion.

Projector tilted up

Corrected image

If your image is shaped like

projector off to one side of the screen at an angle. Place it

directly in front of the center of the screen, facing the screen

squarely.

Using Keystone Correction

To adjust your image when it is wider on the top or bottom,

do the following:

❏ Press the

buttons on the projector until you are

satisfied with the shape of the image.

Note: The image will be slightly shorter after adjusting.

buttons on the projector's

Projector tilted down

, you've placed the

Keystone

buttons

❏ Or press the

on the remote control, select

the

menu, and

Settings

press

. From the

Enter

Settings menu, select

and press

Keystone

Use the

pointer button

on the remote control to

adjust the keystone setting as

needed.

Correcting Computer Images

If the projector is connected to a computer and the image

doesn't look right, press the

control (or the

Enter

panel). This automatically resets the projector's tracking, sync,

resolution, and position settings.

Note: You must be projecting an image for this button to have any

effect. The Auto button works only with computer images. Make

sure Auto Setup is turned on to adjust the source automatically.

If vertical stripes appear in the projected image and the

button doesn't correct the problem, adjust the projector's

Tracking setting. See the User's Guide for instructions.

If the image appears fuzzy or flickers and the

doesn't correct the problem, adjust the projector's Sync

setting. See the User's Guide for instructions.

Adjusting the Volume

You can use the buttons on

the remote control or

projector to increase or

decrease the volume for the

projector's built-in speaker or

an external speaker system

connected to the projector.

Press the

button to

increase the volume, or the

button to decrease it.

Note: You can also adjust the volume using the projector's menu

system. See the User's Guide for instructions.

12/07

Epson PowerLite 6110i

button

Enter

button on the remote

Auto

button on the projector's control

Auto

button