Siemens HB-37 Series Kullanım Kılavuzu ve Kurulum Talimatları - Sayfa 11
Fırın Siemens HB-37 Series için çevrimiçi göz atın veya pdf Kullanım Kılavuzu ve Kurulum Talimatları indirin. Siemens HB-37 Series 32 sayfaları.
Sayfayı Yazdır
is highlighted on the display.
Requirement:
Use the
button to reset the timer duration to zero.
▶
a After a few seconds, the appliance applies the
change and
goes out.
9.3 Setting the cooking time
You can set a cooking time for operation of up to 23
hours 59 minutes.
Requirement: The type of heating and temperature or
setting are set.
Press the
button repeatedly until
1.
in the display.
Use the
or
button to set the cooking time.
2.
Button
Default value
10 minutes
30 minutes
The cooking time can be set in 1-minute increments
up to 1 hour, and then in 5-minute increments.
a The appliance starts heating and the cooking time
counts down after a few seconds.
a If the cooking time has elapsed, an audible signal
sounds and the display shows the cooking time as
zero.
When the cooking time has elapsed:
3.
Press any button to end the audible signal before
‒
it sounds.
To set a cooking time again, press the
‒
When your food is ready, switch off the appli-
‒
ance.
Changing the cooking time
You can change the cooking time at any time.
is highlighted on the display.
Requirement:
Change the cooking time using the
▶
a The appliance applies the change after a few
seconds.
Cancelling the cooking time
You can cancel the cooking time at any time.
is highlighted on the display.
Requirement:
Reset the cooking time to zero using the
▶
a After a few seconds, the appliance applies the
change and continues to heat without a cooking
time.
9.4 Setting the end time
You can delay the time at which cooking is due to fin-
ish by up to 23 hours and 59 minutes.
Notes
¡ The end time cannot be set for types of heating with
grill function.
¡ In order to achieve a good cooking result, do not
delay the end time once the appliance is already in
operation.
¡ Food will spoil if you leave it in the cooking com-
partment too long.
Requirements
¡ The type of heating and temperature or setting are
set.
¡ A cooking time is set.
1.
2.
a The display shows the calculated end time.
3.
a After a few seconds, the appliance applies the set-
a Once the calculated start time has been reached,
a Once the time has elapsed, an audible signal
is highlighted
4.
Changing the end time
In order to achieve a good cooking result, you can only
change the set end time before operation starts and
the cooking time starts counting down.
Requirement:
▶
a The appliance applies the change after a few
Cancelling the end time
You can delete the set end at any time.
button.
Requirement:
▶
a After a few seconds, the appliance applies the
or
button.
9.5 Setting the time on the clock
Once the appliance has been connected to the mains
or following a power failure, the time flashes on the dis-
play. The time starts at "12:00". Set the current time.
Requirement: The function selector must be set to the
"Off" position .
button.
1.
2.
a The time that is set appears on the display.
Tip: You can go to the basic settings → Page 14 to
specify whether or not the time should be shown on
the display.
Changing the time on the clock
You can change the time on the clock at any time.
Requirement: The function selector must be set to the
"Off" position .
1.
2.
a The appliance applies the change after a few
Press the
button repeatedly until
in the display.
Press the
or
button.
Use the
or
button to delay the end time.
ting and the display shows the set end time.
the appliance starts heating up and the cooking
time starts counting down.
sounds and the display shows the cooking time as
zero.
When the cooking time has elapsed:
Press any button to end the signal prematurely.
‒
To set another cooking time, press the
‒
When your food is ready, switch off the appli-
‒
ance.
is highlighted on the display.
Use the
or
button to delay the end time.
seconds.
is highlighted on the display.
Reset the end time to the current time plus the set
cooking time using the
change and starts heating up. The cooking time
counts down.
Use the
or
button to set the time.
Press the
button.
Press the
button repeatedly until
in the display.
Use the
or
button to change the time.
seconds.
Time-setting options en
is highlighted
button.
button.
is highlighted
11