Epson CX7800 - Stylus Color Inkjet Manuel - Sayfa 7
Hepsi Bir Arada Yazıcı Epson CX7800 - Stylus Color Inkjet için çevrimiçi göz atın veya pdf Manuel indirin. Epson CX7800 - Stylus Color Inkjet 19 sayfaları. Epson scan icm updater v1.20 (psb.2008.07.001)
Ayrıca Epson CX7800 - Stylus Color Inkjet için: Teknik Özellikler (2 sayfalar), Teknik Özet (6 sayfalar), Hızlı Başlangıç Kılavuzu (12 sayfalar), Buradan Başlayın Kılavuzu (8 sayfalar), Güncelleme (1 sayfalar)
Sayfayı Yazdır
Copying a Photo
1. Make sure the Epson Stylus
CX7800 is turned on.
2. Place the photo on the glass as
described on page 6. Be sure to
close the document cover.
3. Load up to 20 sheets of letter-size, 4 × 6-inch, or 5 × 7-inch
photo paper, as described on page 4.
4. Press the
Film/Photo
5. Press the l or r
Photo/Options
.
Photograph
When
Restoration ON
with color restoration on. For more information, see page 9.
6. Press the x
button.
Start
The P
light flashes and the Epson Stylus CX7800 scans
On
the photograph and displays it on the LCD screen.
7. Press the u or d
Copies
copies.
8. Press the paper type button to select
9. Press the paper size button to select
.
5"x7"
10. Press the x
button.
Start
The P
light flashes and the Epson Stylus CX7800 starts
On
printing.
To cancel copying, press the y
button. Do not pull out paper that is being printed; it will
be ejected automatically to the output tray.
Note:
The copies may not be exactly the same size as the original.
Making Prints from Slides or
Negatives
You can use the film holder that came with your Epson Stylus
CX7800 to scan 35 mm slides, or strips of negative and
positive film. To get professional results that look and feel like
traditional photos, try one of the special Epson papers listed
on page 1.
Before you scan and print see:
❏ "Placing 35mm Slides in the Holder" (see below)
❏ "Placing 35mm Film Strips in the Holder" on page 7
mode button.
button to select
Copy
is also selected, the photo is copied
button to select the number of
.
Photo Paper
,
, or
Letter
4"x 6"
Stop/Clear Settings
Placing 35mm Slides in the Holder
1. Open the document cover and
remove the document mat. Pull
up on the fastener at the top of
the document mat. Then pull
out the mat.
2. Place the film holder's tabs into
the two small holes at the left edge of the glass. Make sure
the cutouts for 35mm slides are toward the back of the glass
to align them with the fluorescent lamp when you close the
document cover.
3. Place your slides in the film holder in the orientation shown
below with the shiny side up.
Note:
Make sure there is no gap between the holder and the document
table; otherwise the prints may not be clear.
Continue with the steps on page 8 to scan and print your
photos.
Placing 35mm Film Strips in the Holder
1. Open the document cover and
remove the document mat. Pull
up on the fastener at the top of
the document mat. Then pull out
the mat.
8/05
Epson Stylus CX7800
Fluorescent lamp
Epson Stylus CX7800
7
-