Cisco MXP Series Fiziksel Arayüz Kılavuzu - Sayfa 11
Konferans Sistemi Cisco MXP Series için çevrimiçi göz atın veya pdf Fiziksel Arayüz Kılavuzu indirin. Cisco MXP Series 28 sayfaları.
Sayfayı Yazdır
MXP Series Codecs
Contents
Video Sockets
The system will
automatically
S-video input Mini-DIN sockets
adapt to a PAL or
Main camera
NTSC input.
Single
Dual
S-video output Mini-DIN sockets
DVI-I pin-out
NOTE:
TANDBERG supports DVI-D
Single-Link, DVI-A and DVI-I
Single-Link format cables.
DVI-D cables transmit digital
T.M.D.S. signals, DVI-A cables
transmit analogue VGA signals and
DVI-I cables can transmit either
digital or analogue signals.
If your DVI cable is not long enough,
use extension cables. Observe,
however, that the maximum cable
length should not exceed 5 m to
avoid quality loss.
D14790.01 MXP Series Codec Physical Interface Guide, May 2011.
© 2011 Cisco Systems, Inc. All rights reserved.
Introduction
Composite video input RCA sockets
Aux. camera
Doc. camera
Single
Dual
Composite video output RCA sockets
DVI-I Pin-out
Pin
Assignment
Pin
Assignment
1
T.M.D.S. Data
9
T.M.D.S. Data
2–
1–
2
T.M.D.S. Data
10
T.M.D.S. Data
2+
1+
3
T.M.D.S. Data
11
T.M.D.S. Data
2/4 Shield
1/3 Shield
4
T.M.D.S. Data
12
T.M.D.S. Data
4–
3–
5
T.M.D.S. Data
13
T.M.D.S. Data
4+
3+
6
DDC Clock
14
+5 V power
7
DDC Data
15
GND
(return for +5 V,
HSync and
Vsync)
8
Analogue
16
Hot plug detect
Vertical Sync
C1
Analogue Red
C2
Analogue
Green
C4
Analogue
C5
Analogue GND
Horizontal Sync
(analogue
R, G & B return)
Codec 6000 MXP
Codec 6000 MXP
PC DVI-I input sockets
VCR
(Digital Video Interface,
Integrated digital
and analogue)
Single
Dual
DVI output sockets
Formats supported on DVI-I out:
SVGA (800 × 600) 75 Hz
XGA (1024 × 768) 60 Hz
Pin
Assignment
SXGA (1280 × 1024) 60 Hz
HD720p (1280 × 720) 50 Hz, 60 Hz
17
T.M.D.S. Data
WXGA (1280×768) 60 Hz
0–
Formats supported on DVI-I in:
18
T.M.D.S. Data
0+
SVGA (800 × 600) 60 Hz, 72 Hz,
75 Hz, 85 Hz
19
T.M.D.S. Data
XGA (1024 × 768) 60 Hz, 70 Hz, 75 Hz
0/5 Shield
SXGA (1280 × 1024) 60 Hz
20
T.M.D.S. Data
HD720p (1280 × 720) 50 Hz, 60 Hz
5–
21
T.M.D.S. Data
5+
22
T.M.D.S. Clock
Shield
Do as follows to get WXGA:
23
T.M.D.S. Clock+
1 VGA Out Quality must be set to Auto.
2 VGA Monitor Format must be set to Wide.
3 PC Picture Format must be set to Normal.
24
T.M.D.S. Clock–
If you are using TANDBERG supplied monitors this will give
WXGA out when displaying graphics.
C3
Analogue Blue
If non-TANDBERG provided displays are used, you must in
addition execute the command:
xConfiguration Video Outputs AllowWXGA: On
11
Physical interface guide
Codec 3000 MXP
Note that the S-Video/Composite outputs on
the 6000 MXP are now by default turned off
from factory. Ref.
xConfiguration Video
Outputs TV [1..2] Mode
Levels
Composite: 1 Vpp, 75 W
S-Video (Y/C):
Y: 1 Vpp, 75 W
C (PAL): 0.3 Vpp, 75 W
C (NTSC): 0.28 Vpp,
75 W
Contact us
S-video Mini-DIN pin-out
External view of socket
4
3
2
1
Pin 1: Ground (Luminance)
Pin 2: Ground (Chrominance)
Pin 3: Luminance (Y)
Pin 4: Chrominance (C)
RCA pin-out
External view of socket
Signal
GND
www.cisco.com