Toshiba Carrier MMC-AP0181H2UL Kurulum Kılavuzu - Sayfa 13

Klima Toshiba Carrier MMC-AP0181H2UL için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Toshiba Carrier MMC-AP0181H2UL 18 sayfaları. Air conditioner (multi type)

Sayfayı Yazdır

Ceiling type

Filter sign setting

According to the installation condition, the lighting time

of the filter sign (Notification of filter cleaning) can be

changed.

Follow to the basic operation procedure

→

(

• For the CODE No. in Procedure

, specify [01].

• For the [Set data] in Procedure

, select the SET

DATA of filter sign lighting time from the following

table.

SET DATA

Filter sign lighting time

0000

None

0001

150 H

0002

2500 H (Factory default)

0003

5000 H

0004

10000 H

To secure better effect of

heating

When it is difficult to obtain satisfactory heating due to

installation place of the indoor unit or structure of the

room, the detection temperature of heating can be

raised. Also use a circulator or other device to circulate

heat air near the ceiling.

Follow to the basic operation procedure

→

(

• For the CODE No. in Procedure

, specify [06].

• For the set data in Procedure

, select the SET

DATA of shift value of detection temperature to be

set up from the table below.

SET DATA

Detection temp shift value

0000

No shift

0001

+1.8 °F (+1 °C)

+3.6 °F (+2 °C)

0002

(Factory default)

0003

+5.4 °F (+3 °C)

0004

+7.2 °F (+4 °C)

0005

+9.0 °F (+5 °C)

0006

+10.8 °F (+6 °C)

23-EN

Installation Manual

Remote control sensor

The temperature sensor of the indoor unit senses room

temperature usually. Set the remote control sensor to

sense the temperature around the remote control.

Select items following the basic operation procedure

→

(

• Specify [32] for the CODE No. in Procedure

• Select the following data for the SET DATA in

Procedure

SET DATA

0000

0001

Remote control

Not used

Used

sensor

(factory setting)

When

flashes, the remote control sensor is

defective.

Select the SET DATA [0000] (not used) or replace the

remote control.

Group control

In a group control, a remote control can control up to

maximum 8 units.

• The wired remote control only can control a group

control. The wireless remote control is unavailable

for this control.

• For wiring procedure and wires of the individual line

(Identical refrigerant line) system, refer to "Electric

work" in this Manual.

• Wiring between indoor units in a group is performed

in the following procedure.

• Connect the indoor units by connecting the remote

control wires from the remote control terminal blocks

(A, B) of the indoor unit connected with a remote

control to the remote control terminal blocks (A, B) of

the other indoor unit. (Non-polarity)

• For address setup, refer to the Installation Manual

attached to the outdoor unit.

Ceiling type

Test Run

Before test run

• Before turning on the circuit breaker, carry out the

following procedure.

1) By using 500V-megger, check that resistance of

1MΩ or more exists between the terminal block L

to L

and the ground (grounding).

If resistance of less than 1MΩ is detected, do not

run the unit.

2) Check the valve of the outdoor unit being opened

fully.

• To protect the compressor at activation time, leave

power-ON for 12 hours or more be for operating.

• Before starting a test run, be sure to set addresses

following the Installation Manual supplied with the

outdoor unit.

Execute a test run

Operate the unit with the remote control as usual.

For the procedure of the operation, refer to the

attached Owner's Manual.

A forced test run can be executed in the following

procedure even if the operation stops by thermo.-OFF.

In order to prevent a serial operation, the forced test

run is released after 60 minutes have passed and

returns to the usual operation.

CAUTION

• Do not use the forced test run for cases other than the

test run because it applies an excessive load to the

devices.

Wired remote control

1,5

Procedure

Push

button for 4 seconds or more. [TEST] is

displayed on the display part and the selection of mode

in the test mode is permitted.

– 12 –

Installation Manual

Procedure

Push

button.

Procedure

Select the operation mode with

or [HEAT].

• Do not run the air conditioner in a mode other than

[COOL] or [HEAT].

• The temperature controlling function does not work

during test run.

• The detection of error is performed as usual.

Procedure

After the test run, push

button to stop a test

run.

(Display part is same as procedure 1.)

Procedure

Push

check button to cancel (release from) the test

run mode.

([TEST] disappears on the display and the status

returns to a normal.)

2, 4

button, [COOL]

24-EN