Epson PowerLite 8300i with EasyMP.net module Hızlı Kılavuz - Sayfa 19

Yazılım Epson PowerLite 8300i with EasyMP.net module için çevrimiçi göz atın veya pdf Hızlı Kılavuz indirin. Epson PowerLite 8300i with EasyMP.net module 20 sayfaları. Release of check tool for network projectors v1.00 for windows
Ayrıca Epson PowerLite 8300i with EasyMP.net module için: Kullanıcı Kılavuzu (42 sayfalar), Kullanım Kılavuzu (36 sayfalar), Kullanım Kılavuzu (47 sayfalar), Hızlı Kurulum (2 sayfalar), Ürün Destek Bülteni (27 sayfalar), Parça Listesi (1 sayfalar), Tamamlayıcı Kılavuz (2 sayfalar), Broşür ve Teknik Özellikler (2 sayfalar), Kullanıcı Kılavuzu (1 sayfalar), Ürün Destek Bülteni (25 sayfalar), Ürün Destek Bülteni (22 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (41 sayfalar), Ürün Destek Bülteni (34 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (15 sayfalar), Ürün Destek Bülteni (22 sayfalar), Hızlı Kurulum (2 sayfalar)

Sayfayı Yazdır
Epson PowerLite 8300i with EasyMP.net module Hızlı Kılavuz
EPSON PowerLite 8300i Projector

Replacing the Lamp

The projection lamp typically lasts for about 3000 hours in
low-brightness mode, or 2000 hours in high-brightness mode.
Note: The brightness setting can be changed by selecting
in the projector's Advanced2 menu.
Brightness Control
It is time to replace the lamp when:
The projected image gets darker or starts to deteriorate.
The message
LAMP REPLACE
the lamp comes on and the lamp warning light
flashing orange. To maintain projector brightness and
image quality, replace the lamp as soon as possible.
The lamp warning light
burnt out).
Contact your dealer or call EPSON at (800) 873-7766 in the
United States for a replacement lamp. Request part number
. In Canada, please call (800) 463-7766 for
V13H010L23
dealer referral
Follow these steps to replace the lamp:
1. Turn off the projector.
2. When the power light stops flashing, unplug the power
cord and let the projector cool.
Warning: Let the projector cool for at least half an hour, if it
has been on. The lamp is extremely hot immediately after use.
3. If the projector is mounted on the ceiling, remove the rear
cover.
18
EPSON PowerLite 8300i Projector
-
appears on the screen when
is
is flashing red (the lamp is
Release tab to
remove rear cover
4. Loosen the lamp cover screws (you don't need to take them
out all the way). Then remove the cover.
5. Loosen the three screws holding the lamp in place (you
can't remove them).
6. Grasp the wire handle as shown and pull the lamp straight
out.
7. Gently insert the new lamp.
8. Once the lamp is fully inserted, tighten its screws and
replace the cover. (The projector won't come on if the lamp
cover is loose.)
9. Reset the lamp timer (select
projector's
About
5/03
1
2
Reset Lamp Timer
menu).
in the