Pioneer AVH-P3200BT Kurulum Kılavuzu

Alıcı Pioneer AVH-P3200BT için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Pioneer AVH-P3200BT 8 sayfaları. Dvd, rds, av receiver
Ayrıca Pioneer AVH-P3200BT için: Kurulum Kılavuzu (40 sayfalar)

Sayfayı Yazdır

DVD RDS AV RECEIVER

DVD RDS AV РЕСИВЕР

AVH-P4200DVD

AVH-P3200BT

Installation Manual

Руководство по установке

Printed in Thailand

Отпечатано в Таиланде

<CRD4451-A/N> UW

Connecting the units

WARNING

• To avoid the risk of accident and the potential

LIGHT GREEN LEAD AT POWER CONNECTOR

violation of applicable laws, the front DVD or TV

IS DESIGNED TO DETECT PARKED STATUS

(sold separately) feature should never be used

AND MUST BE CONNECTED TO THE POWER

while the vehicle is being driven. Also, rear displays

SUPPLY SIDE OF THE PARKING BRAKE SWITCH.

should not be in a location where it is a visible

IMPROPER CONNECTION OR USE OF THIS LEAD

distraction to the driver.

MAY VIOLATE APPLICABLE LAW AND MAY RESULT

• In some countries or states the viewing of images

IN SERIOUS INJURY OR DAMAGE.

on a display inside a vehicle even by persons

other than the driver may be illegal. Where such

regulations apply, they must be obeyed and this

unit's DVD features should not be used.

CAUTION

• PIONEER does not recommend that you install

or service your display yourself. Installing or

servicing the product may expose you to risk

of electric shock or other hazards. Refer all

installation and servicing of your display to

authorized Pioneer service personnel.

• Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wiring to

remain exposed.

• Do not drill a hole into the engine compartment

to connect the yellow lead of the unit to

the vehicle battery. Engine vibration may

eventually cause the insulation to fail at

the point where the wire passes from the

passenger compartment into the engine

compartment. Take extra care in securing the

wire at this point.

• It is extremely dangerous to allow the display

lead to become wound around the steering

column or gearshift. Be sure to install the

display in such a way that it will not obstruct

driving.

• Make sure that wires will not interfere with

moving parts of the vehicle, such as the

gearshift, parking brake or seat sliding

mechanism.

• Do not shorten any leads. If you do, the

protection circuit may fail to work properly.

Connecting the units

• When this unit is on, control signals are sent

Important

through the blue/white cable. Connect this cable to

the system remote control of an external power amp

• This unit cannot be installed in a vehicle without

or the vehicle's auto-antenna relay control terminal

ACC (accessory) position on the ignition switch.

(max. 300 mA 12 V DC). If the vehicle is equipped

with a glass antenna, connect it to the antenna

booster power supply terminal.

• Never connect the blue/white cable to the power

terminal of an external power amp. Also, never

connect it to the power terminal of the auto

antenna. Doing so may result in battery drain or a

malfunction.

• IP-BUS connectors are color-coded. Be sure to

connect connectors of the same color.

ACC position

No ACC position

• The black cable is ground. Ground cables for

this unit and other equipment (especially, high-

current products such as power amps) must be

• Use of this unit in conditions other than the

following could result in fire or malfunction.

wired separately. If they are not, an accidental

— Vehicles with a 12-volt battery and negative

detachment may result in a fire or malfunction.

grounding.

— Speakers with 50 W (output value) and 4 ohm to

8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunction,

be sure to follow the directions below.

— Disconnect the negative terminal of the battery

before installation.

— Secure the wiring with cable clamps or adhesive

tape. Wrap adhesive tape around wiring that

comes into contact with metal parts to protect

the wiring.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.

— Cover any disconnected cable connectors with

insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power with other

devices. The current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly to

ground.

— Never band together negative cables of multiple

speakers.

Connecting the units

When connecting to separately sold power amp

Rear output

Front output

Power amp

(sold separately)

To rear output

Power amp

(sold separately)

To front output

(AVH-

Power amp

Subwoofer output

P4200DVD

(sold separately)

This product

To subwoofer

only)

output

Connect with RCA cables

(sold separately)

Blue/white

Connect to system control

terminal of the power amp

(max. 300 mA 12 V DC).

System remote control

Blue/white (6*)

Blue/white (5*)

Connect to auto-antenna

relay control terminal

(max. 300 mA 12 V DC).

The pin position of the ISO connector will differ

Left

Right

depending on the type of vehicle. Connect 5*

and 6* when Pin 5 is an antenna control type. In

another type of vehicle, never connect 5* and 6*.

•When you connect the separately sold



multi-channel processor (DEQ-P6600) to this

Subwoofer

unit, do not connect anything to the speaker



leads and system remote control (blue/white).

•When you connect the multi-channel

processor to this unit, refer to multi-channel

processor's installation manual for the



connection method.

Front speaker





Rear speaker



Perform these connections when

using the optional amplifier.