Aeotec MULTISENSOR 6 Manuel

Aksesuarlar Aeotec MULTISENSOR 6 için çevrimiçi göz atın veya pdf Manuel indirin. Aeotec MULTISENSOR 6 3 sayfaları. Z-wave water and flood sensor
Ayrıca Aeotec MULTISENSOR 6 için: Kullanıcı Kılavuzu (13 sayfalar), Kullanıcı Kılavuzu (8 sayfalar), Manuel (10 sayfalar), Kullanıcı Kılavuzu (13 sayfalar)

Sayfayı Yazdır

Aeotec by Aeon Labs Water Sensor 6.

Aeotec by Aeon Labs Water Sensor 6 brings intelligence

to a new level, one that is suited to both safety and

convenience. It contains 4 sensing points, which would be

more accurately to detect the presence and absence of

water or detect whether there is water leak in some places

Water Sensor 6

of your home. The Water Sensor 6 has an inbuilt buzzer that

can play alarm sounds to let you know when the water is

detected.

View the expanded manual:

The Water Sensor 6 is also a security Z-Wave device that

http://aeotec.com/support

supports Over The Air (OTA) for firmware updates.

Familiarize yourself with your Water Sensor 6.

Package contents:

Main sensor unit (×1).

CR123A battery (×1).

S crew (×2).

Main sensor unit

CR123A battery

Secure the Sensor plate using the screw

provided.

Sensor

Buzzer

Sensor probe 1

probe 2

Sensor probe 3

Sensor

RGB

probe 4

LED

Action Button

(Front)

(Back)

Quick start.

Power on your Sensor.

Remove the pull tab by pulling it away from the

After complete the securing of the Sensor plate,

Water Sensor.

your Water Sensor unit will possess the high

waterproof level of IP65.

Your Water Sensor 6 also can be powered by the

Pull it from the Water Sensor

Water Sensor 6 Dock and connect to external

sensor probes or ropes, if you want to know more

about it, please refer to the Water Sensor 6 Dock

manual.

Adding your Sensor to your Z-Wave network.

With your sensor is powered on, it's time to add it

Now, you can try pressing the Sensor's Action

to your Z-Wave network.

Screw

Button, if you can see the RGB LED blinks, which

1. Let your Z-Wave primary controller/gateway

indicates that the Sensor is powered on.

enter into adding/inclusion mode.

For example, you can put it on the floor or

Take your Sensor near to your primary

somewhere of your washroom or kitchen and

controller.

so on. In case, your washroom's water pipe

Press the Action Button once on your Sensor,

is ruptured or the water leakage happens

the green LED will blink.

without knowing it. However, the Water Sensor

If your Water Sensor has been successfully

detected this water leakage event, it sends out

added to your Z-Wave network, its green LED

the notification message immediately to tell your

will be solid for 2 seconds and then the orange

home gateway to shut off the main water gate of

LED will fast blink for 10 minutes if the Sensor

your home for avoiding water leakage accident.

does not receive the Wake Up No More info

At the same time, the buzzer keeps playing alarm

sounds to tell the people at home that the water

Command from Controller. If the adding was

unsuccessful and the red LED will be solid for

leak is detected.

2 seconds and then become colourful gradient

for a few seconds before it turns off, repeat the

above steps.

With your Sensor now working as a part of your

smart home, you'll be able to configure it from

your home control software or phone application.

Please refer to your software's user guide for

precise instructions on configuring the Water

Sensor to your needs.

Installing your Water Sensor.

If you want to detect whether or not there would

be water leakage from the fridge, you can put the

The installation of your Water Sensor is very

Water Senor near to the fridge. Just note that the

simple, since you just need to select where you'll

Water Sensor cannot be put inside the fridge or

place your Water Sensor in your home to detect

other metal container, since the metal container

whether there is water leakage.

will affect the signal strength of the Sensor unit

Water is detected by the Sensing point 1 and 2

and your main controller.

Water is detected by the Sensing point 3 and 4

Water is detected by the Sensing point 1,2,3 and 4

Water

Water Sensor triggering.

The Water Sensor will be triggered when the water

leak or presence happens in below situations:

Water is detected by the Sensing point 2 and 4.

Water

Water is detected by the Sensing point 1 and 3.

The above situations are the water leak or water

Water

presence event is triggered by the Sensor, when

the water recedes from the Sensor, the water leak

event will be cleared and then the Sensor will

Water