Aeotec MULTISENSOR 6 Manual
Procurar online ou descarregar pdf Manual para Acessórios Aeotec MULTISENSOR 6. Aeotec MULTISENSOR 6 3 páginas. Z-wave water and flood sensor
Também para Aeotec MULTISENSOR 6: Manual do utilizador (13 páginas), Manual do utilizador (8 páginas), Manual (10 páginas), Manual do utilizador (13 páginas)
Imprimir página
1
Aeotec by Aeon Labs Water Sensor 6.
Aeotec by Aeon Labs Water Sensor 6 brings intelligence
to a new level, one that is suited to both safety and
convenience. It contains 4 sensing points, which would be
more accurately to detect the presence and absence of
water or detect whether there is water leak in some places
Water Sensor 6
of your home. The Water Sensor 6 has an inbuilt buzzer that
can play alarm sounds to let you know when the water is
detected.
View the expanded manual:
The Water Sensor 6 is also a security Z-Wave device that
http://aeotec.com/support
supports Over The Air (OTA) for firmware updates.
2
Familiarize yourself with your Water Sensor 6.
Package contents:
1.
Main sensor unit (×1).
2.
CR123A battery (×1).
3.
S crew (×2).
Main sensor unit
CR123A battery
2.
Secure the Sensor plate using the screw
provided.
Sensor
Buzzer
Sensor probe 1
probe 2
Sensor probe 3
Sensor
RGB
probe 4
LED
Action Button
(Front)
(Back)
Quick start.
3
Power on your Sensor.
1.
Remove the pull tab by pulling it away from the
After complete the securing of the Sensor plate,
Water Sensor.
your Water Sensor unit will possess the high
waterproof level of IP65.
Your Water Sensor 6 also can be powered by the
Pull it from the Water Sensor
Water Sensor 6 Dock and connect to external
sensor probes or ropes, if you want to know more
about it, please refer to the Water Sensor 6 Dock
manual.
Adding your Sensor to your Z-Wave network.
With your sensor is powered on, it's time to add it
Now, you can try pressing the Sensor's Action
to your Z-Wave network.
Screw
Button, if you can see the RGB LED blinks, which
1. Let your Z-Wave primary controller/gateway
indicates that the Sensor is powered on.
enter into adding/inclusion mode.
For example, you can put it on the floor or
2.
Take your Sensor near to your primary
somewhere of your washroom or kitchen and
controller.
so on. In case, your washroom's water pipe
3.
Press the Action Button once on your Sensor,
is ruptured or the water leakage happens
the green LED will blink.
without knowing it. However, the Water Sensor
4.
If your Water Sensor has been successfully
detected this water leakage event, it sends out
added to your Z-Wave network, its green LED
the notification message immediately to tell your
will be solid for 2 seconds and then the orange
home gateway to shut off the main water gate of
LED will fast blink for 10 minutes if the Sensor
your home for avoiding water leakage accident.
does not receive the Wake Up No More info
At the same time, the buzzer keeps playing alarm
sounds to tell the people at home that the water
Command from Controller. If the adding was
unsuccessful and the red LED will be solid for
leak is detected.
2 seconds and then become colourful gradient
for a few seconds before it turns off, repeat the
above steps.
With your Sensor now working as a part of your
smart home, you'll be able to configure it from
your home control software or phone application.
Please refer to your software's user guide for
precise instructions on configuring the Water
Sensor to your needs.
Installing your Water Sensor.
If you want to detect whether or not there would
be water leakage from the fridge, you can put the
The installation of your Water Sensor is very
Water Senor near to the fridge. Just note that the
simple, since you just need to select where you'll
Water Sensor cannot be put inside the fridge or
place your Water Sensor in your home to detect
other metal container, since the metal container
whether there is water leakage.
will affect the signal strength of the Sensor unit
3.
Water is detected by the Sensing point 1 and 2
and your main controller.
4.
Water is detected by the Sensing point 3 and 4
5.
Water is detected by the Sensing point 1,2,3 and 4
Water
3
Water Sensor triggering.
The Water Sensor will be triggered when the water
leak or presence happens in below situations:
1.
Water is detected by the Sensing point 2 and 4.
Water
2.
Water is detected by the Sensing point 1 and 3.
5
The above situations are the water leak or water
Water
Water
presence event is triggered by the Sensor, when
the water recedes from the Sensor, the water leak
event will be cleared and then the Sensor will
2
1
Water
4