Whirlpool 3395339 Kurulum Talimatları Kılavuzu - Sayfa 5

Kurutucu Whirlpool 3395339 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Whirlpool 3395339 12 sayfaları. Coin-operated stacked dryers

Sayfayı Yazdır

Exhaust

requirements

Fire/Health

Hazard

Do Not use non-metal,

flexible

duct.

Do Not use metal duct smaller

than four inches in diameter.

Do Not use exhaust

hoods with

metal latches.

Check

that exhaust

system is not

longer than specified.

Exhaust

system longer than specified

will:

Accumulate

lint.

Shorten the life of the dryer.

Reduce

the performance,

resulting

in longer drying times

and increased

energy

usage.

Failure to follow specifications

may

result in a fire.

Do Not exhaust

dryers into a

chimney,

furnace

cold air duct,

attic or crawl space,

or any other

duct used for venting.

9 Clean the exhaust

system every

other year.

Do Not install flexible

duct in

enclosed

walls, ceilings

or floors.

Accumulated

lint could result in a

fire or cause moisture

damage.

. Exhaust dryers outside to prevent

exposure

to substances

in gas

fuels and combustion

which may

be harmful to your health.

The moisture

and lint indoors may

cause:

- FIRE HAZARD from lint collected

dryer.

- Moisture

damage

to woodwork,

furniture,

paint, wallpaper,

carpet,

etc.

- Housecleaning

problems

and

possible

health problems.

Failure to follow these instructions

could result in fire damage

personal

injury.

Exhaust materials

are not

supplied.

Four-inch

metal exhaust

duct is

required.

Plan installation

to use the

fewest number

of elbows

and turns.

Use duct tape

to seal all joints.

Metal flexible

duct must be fully

extended

and supported

when the

dryers are in final position.

DO NOT

KINK OR CRUSH THE DUCT. The metal

flexible

duct must be completely

open to allow adequate

exhaust

air

to flow.

Allow as much room as possible when

using elbows

or making

turns. Bend

duct gradually

to avoid kinking.

Remove

excess flexible

duct to avoid

sagging

and kinking that may cause

reduced

airflow.

The external

exhaust

ducts can be

routed

straight out the back of the

dryers. Kits are available

to convert

the external

exhaust

duct to be

routed

right, left or through

the

bottom.

See Page 6. Product

dimensions

and recessed

area

requirements

are given on Page 7.

Side or bottom

exhaust:

The maximum

length of the exhaust

system if dryer is

exhausted

out the side or bottom

is 16

feet with two external

elbows

and

hood.

flexible

duct is shown in the chart.

Rear exhaust:

The maximum

length of

the exhaust

system depends

on the

type of duct, the number

of elbows

and the type of exhaust

hood. The

maximum

length for both rigid and

This chart applies

only to individually

exhausted

units.

EXHAUST HOOD TYPE

MAXIMUM

LENGTH OF 4-INCH

DIAMETER RIGID METAL DUCT

43 FT.

41 FT.

36 FT.

33 FT.

31 FT.

26 FT.

23 FI.

21 FT.

16 FT.

MAXIMUM

LENGTH OF I-INCH

DIAMETER FLEXIBLE METAL DUCT

30 FT.

29 FT.

24 FT.

23 FT.

18 FT.

16 FT.

15 FT.

10 FT.

For exhaust

systems not covered

the exhaust

length chart, see

WhirlDool Service

Manual,

"Exhausting

Whirlpool

Dryers," Part No. 603197,

available

from your Whirlpool

parts

distributor.

Service

check:

The back pressure in

any exhaust

system used must not

exceed

0.6 inches of water column

measured

with an inclined

manometer

at the point that the

exhaust

system connects

to the

dryers.

If dryers are installed

in a confined

area such as a bedroom,

bathroom

or closet, they must be exhausted

the outside and provision

must be

made

for enough

air for combustion

and ventilation.

(Check

governing

codes and ordinances.

Also refer to

the "Recessed

area and closet

installation

instructions,"

Page 7.)

An exhaust

hood should cap the

exhaust

duct to prevent

exhausted

air from returning

into the dryers. The

outlet hood must be at least 12

inches from the ground

or any object

that may be in the path of the

exhaust.

Four-inch

outlet hood is preferred.

However,

a 2- l/2-inch

outlet exhaust

hood may be used. (A 2-l/2-inch

outlet creates

greater

back pressure

than other hoods.)

A main exhaust

duct can be used for

exhausting

a group of dryers. Main

exhaust

duct should be sized to

remove

200 CFM of air per dryer.

Large-capacity

lint screens of proper

design may be used in the main

exhaust

duct if checked

and

cleaned

frequently.

The room where

the dryers are located

should have

make-up

air equal to or greater

than

the CFM of all the dryers in the room.

Back-draft

damper

kits (Part No.

3391910) are available

from your

Whirlpool

dealer

and should be

installed

in each dryer's exhaust

duct

to prevent

exhausted

air from

returning

into the dryers and to keep

the exhaust

balance

within the main

exhaust

duct. Unobstructed

air

openings

are required.

Each exhaust

duct should enter the

main duct at an angle

pointing

in the

direction

of the airflow.

Ducts

entering

from the opposite

side

should be staggered

to reduce

the

exhausted

air from interfering

with the

other ducts.

The maximum

angle

of each duct

entering

the main duct should be no

more than 30".

Page 5