Xerox WORKCENTRE 7120 Sistem Yöneticisi Kılavuzu - Sayfa 20

Yazıcı Xerox WORKCENTRE 7120 için çevrimiçi göz atın veya pdf Sistem Yöneticisi Kılavuzu indirin. Xerox WORKCENTRE 7120 20 sayfaları. Color networking mfp a3
Ayrıca Xerox WORKCENTRE 7120 için: Değerlendirici El Kitabı (25 sayfalar), Değerlendirici El Kitabı (24 sayfalar), Referans Kılavuzu (30 sayfalar), Teknik Özellikler (14 sayfalar), Teknik Özellikler (14 sayfalar), Rekabetçi Karşılaştırma (11 sayfalar), Rekabetçi Karşılaştırma (11 sayfalar), Broşür ve Teknik Özellikler (4 sayfalar), Referans Kılavuzu (29 sayfalar), Hızlı Kullanım Kılavuzu (20 sayfalar), Hızlı Kullanım Kılavuzu (20 sayfalar), Hızlı Kullanım Kılavuzu (20 sayfalar), Hızlı Kullanım Kılavuzu (20 sayfalar), Kurulum Kılavuzu (2 sayfalar), Kurulum Kılavuzu (2 sayfalar), Hızlı Kullanım Kılavuzu (20 sayfalar), Referans Kılavuzu (32 sayfalar)

Sayfayı Yazdır
Xerox WORKCENTRE 7120 Sistem Yöneticisi Kılavuzu
Network Configuration
TCP/IP
Transmission Control Protocol (TCP) and Internet Protocol (IP) are a two protocols within the Internet
Protocol Suite. IP manages the transmission of messages from computer to computer while TCP
manages the actual end-to-end connections.
Note:
You can configure IPv4 settings at the printer control panel or through CentreWare IS. You
can only configure IPv6 through CentreWare IS.
Enabling TCP/IP
Note:
By default, TCP/IP is enabled. If you disable TCP/IP, you must enable it at the printer control
panel before you can access CentreWare IS.
1.
At the printer control panel, press the Machine Status button, then touch the Tools tab.
2.
Touch Connectivity and Network Setup > Protocol Settings.
3.
Touch TCP/IP - IP Mode, then touch Change Settings.
4.
Touch IPv4 Mode, IPv6, or Dual Stack to enable both IPv4 and IPv6.
Touch Save.
5.
Configuring TCP/IP Settings at the Control Panel
Manually Configuring an IPv4 Network Address
1.
At the printer control panel, press the Machine Status button, then touch the Tools tab.
2.
Touch Connectivity and Network Setup > Protocol Settings.
3.
Touch IPv4 - IP Address Resolution, and touch Change Settings.
Touch Static, then touch Save.
4.
5.
Touch IPv4 - IP Address, and touch Change Settings.
6.
Type the static IP address using the touch-screen keypad, and touch Save.
7.
Touch IPv4 - Subnet Mask, and touch Change Settings.
8.
Type the subnet mask using the touch-screen keypad, and touch Save.
9.
Touch IPv4 - Gateway Mask, and touch Change Settings.
10. Type the gateway mask using the touch-screen keypad, and touch Save.
Manually Configuring an IPv6 Network Address
At the printer control panel, press the Machine Status button, then touch the Tools tab.
1.
2.
Touch Connectivity and Network Setup > Protocol Settings.
Touch IPv6 Address Manual Configuration, then touch Change Settings.
3.
4.
Touch Enabled, then touch Save.
5.
Touch Manually Configured IPv6 Address, then touch Change Settings.
6.
Type the static IP address using the touch-screen keypad, and touch Save.
7.
Touch Manually Configured IPv6 Address Prefix, and touch Change Settings.
20
WorkCentre 7120 Multifunction Printer
System Administrator Guide